DataSheet.es    


PDF W9725G6KB Data sheet ( Hoja de datos )

Número de pieza W9725G6KB
Descripción 4M x 4-BANKS x 16-BIT DDR2 SDRAM
Fabricantes Winbond 
Logotipo Winbond Logotipo



Hay una vista previa y un enlace de descarga de W9725G6KB (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! W9725G6KB Hoja de datos, Descripción, Manual

W9725G6KB
4M 4 BANKS 16 BIT DDR2 SDRAM
Table of Contents-
1. GENERAL DESCRIPTION ...................................................................................................................4
2. FEATURES ...........................................................................................................................................4
3. ORDER INFORMATION .......................................................................................................................5
4. KEY PARAMETERS .............................................................................................................................5
5. BALL CONFIGURATION ......................................................................................................................6
6. BALL DESCRIPTION............................................................................................................................7
7. BLOCK DIAGRAM ................................................................................................................................8
8. FUNCTIONAL DESCRIPTION..............................................................................................................9
8.1 Power-up and Initialization Sequence ...................................................................................................9
8.2 Mode Register and Extended Mode Registers Operation ...................................................................10
8.2.1
Mode Register Set Command (MRS)...............................................................................10
8.2.2
Extend Mode Register Set Commands (EMRS) ..............................................................11
8.2.2.1
Extend Mode Register Set Command (1), EMR (1)................................................11
8.2.2.2
DLL Enable/Disable................................................................................................12
8.2.2.3
Extend Mode Register Set Command (2), EMR (2)................................................13
8.2.2.4
Extend Mode Register Set Command (3), EMR (3)................................................14
8.2.3
Off-Chip Driver (OCD) Impedance Adjustment ................................................................15
8.2.3.1
Extended Mode Register for OCD Impedance Adjustment ....................................16
8.2.3.2
OCD Impedance Adjust ..........................................................................................16
8.2.3.3
Drive Mode .............................................................................................................17
8.2.4
On-Die Termination (ODT)...............................................................................................18
8.2.5
ODT related timings .........................................................................................................18
8.2.5.1
MRS command to ODT update delay.....................................................................18
8.3 Command Function.............................................................................................................................20
8.3.1
Bank Activate Command..................................................................................................20
8.3.2
Read Command ...............................................................................................................20
8.3.3
Write Command ...............................................................................................................21
8.3.4
Burst Read with Auto-precharge Command.....................................................................21
8.3.5
Burst Write with Auto-precharge Command.....................................................................21
8.3.6
Precharge All Command ..................................................................................................21
8.3.7
Self Refresh Entry Command ..........................................................................................21
8.3.8
Self Refresh Exit Command .............................................................................................22
8.3.9
Refresh Command ...........................................................................................................22
8.3.10
No-Operation Command ..................................................................................................23
8.3.11
Device Deselect Command..............................................................................................23
8.4 Read and Write access modes ...........................................................................................................23
8.4.1
Posted CAS ....................................................................................................................23
Publication Release Date: Sep. 03, 2012
- 1 - Revision A03

1 page




W9725G6KB pdf
W9725G6KB
3. ORDER INFORMATION
PART NUMBER
W9725G6KB-18
W9725G6KB-25
W9725G6KB25I
W9725G6KB25A
W9725G6KB25K
W9725G6KB-3
SPEED GRADE
DDR2-1066 (7-7-7)
DDR2-800 (5-5-5) or DDR2-800 (6-6-6)
DDR2-800 (5-5-5) or DDR2-800 (6-6-6)
DDR2-800 (5-5-5) or DDR2-800 (6-6-6)
DDR2-800 (5-5-5) or DDR2-800 (6-6-6)
DDR2-667 (5-5-5)
OPERATING TEMPERATURE
0°C TCASE 85°C
0°C TCASE 85°C
-40°C TCASE 95°C
-40°C TA, TCASE 95°C
-40°C TA, TCASE 105°C
0°C TCASE 85°C
4. KEY PARAMETERS
SYM.
SPEED GRADE
Bin(CL-tRCD-tRP)
Part Number Extension
@CL = 7
@CL = 6
tCK(avg) Average clock period
@CL = 5
@CL = 4
tRCD
tREFI
tRP
tRC
tRAS
IDD0
IDD1
IDD4R
IDD4W
IDD5B
IDD6
IDD7
@CL = 3
Active to Read/Write Command Delay Time
-40°C TCASE 85°C
Average periodic
refresh Interval
0°C TCASE 85°C
85°C < TCASE 95°C
95°C < TCASE 105°C
Precharge to Active Command Period
Active to Ref/Active Command Period
Active to Precharge Command Period
Operating one bank active-precharge current
Operating one bank active-read-precharge current
Operating burst read current
Operating burst write current
Burst refresh current
Self refresh current (TCASE 85C)
Operating bank interleave read current
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Max.
Min.
Min.
Min.
Max.
Max.
Max.
Max.
Max.
Max.
Max.
DDR2-1066
7-7-7
-18
1.875 nS
7.5 nS
2.5 nS
7.5 nS
3 nS
7.5 nS
3.75 nS
7.5 nS
13.125 nS
*2
7.8 μS*1
3.9 μS*4
*6
13.125 nS
58.125 nS
45 nS
70 mA
80 mA
125 mA
130 mA
75 mA
6 mA
160 mA
DDR2-800
5-5-5/6-6-6
-25/25I/25A/25K
2.5 nS
8 nS
2.5 nS
8 nS
3.75 nS
8 nS
5 nS
8 nS
12.5 nS
7.8 μS*2, 3
7.8 μS*1
3.9 μS*4
3.9 μS*5
12.5 nS
57.5 nS
45nS
60 mA
70 mA
105 mA
110 mA
70 mA
6 mA
135 mA
DDR2-667
5-5-5
-3
3 nS
8 nS
3.75 nS
8 nS
5 nS
8 nS
15 nS
*2
7.8 μS*1
3.9 μS*4
*6
15 nS
60 nS
45 nS
55 mA
65 mA
95 mA
100 mA
65 mA
6 mA
115 mA
Notes:
1. All speed grades support 0°C TCASE 85°C with full JEDEC AC and DC specifications.
2. For -18, -25 and -3 speed grades, -40°C TCASE < 0°C is not available.
3. 25I, 25A and 25K speed grades support -40°C TCASE 85°C with full JEDEC AC and DC specifications.
4. For all speed grade parts, TCASE is able to extend to 95°C with doubling Auto Refresh commands in frequency to a 32 mS
period ( tREFI = 3.9 µS) and to enter to Self Refresh mode at this high temperature range via A7 1on EMR (2).
5. For 25K automotive speed grade, TCASE is able to extend to 105°C with doubling Auto Refresh commands in frequency to
a 32 mS period ( tREFI = 3.9 µS) and to enter to Self Refresh mode at this high temperature range via A7 1on EMR (2).
6. For -18, -25, 25I, 25A and -3 speed grades, 95°C < TCASE ≤ 105°C is not available.
Publication Release Date: Sep. 03, 2012
- 5 - Revision A03

5 Page





W9725G6KB arduino
W9725G6KB
SDRAM. Burst address sequence type is defined by A3, CAS Latency is defined by A[6:4]. The DDR2
does not support half clock latency mode. A7 is used for test mode. A8 is used for DLL reset. A7 must
be set to LOW for normal MRS operation. Write recovery time WR is defined by A[11:9]. Refer to the
table for specific codes.
BA1 BA0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
Address Field
0 0 PD
WR
DLL TM
CAS Latency
BT
Burst Length
Mode Register
BA1 BA0
00
01
10
11
A8 DLL Reset
0 No
1 Yes
A7 Mode
0 Normal
1 Test
MRS mode
MR
EMR (1)
EMR (2)
EMR (3)
A12 Active power down exit time
0 Fast exit (use tXARD)
1 Slow exit (use tXARDS)
Write recovery for Auto-precharge
A11 A10
00
00
A9
0
1
WR *
Reserved
2
010
011
100
3
4
5
101
110
111
6
7
8
A3 Burst Type
0 Sequential
1 Interleave
Burst Length
A2 A1 A0
010
011
BL
4
8
CAS Latency
A6 A5 A4
000
001
010
011
100
101
110
111
Latency
Reserved
Reserved
Reserved
3
4
5
6
7
Note:
1. WR (write recovery for Auto-precharge) min is determined by tCK(avg) max and WR max is determined by tCK(avg) min.
WR[cycles] = RU{ tWR[nS] / tCK(avg)[nS] }, where RU stands for round up. The mode register must be programmed to this
value. This is also used with tRP to determine tDAL.
Figure 2 Mode Register Set (MRS)
8.2.2 Extend Mode Register Set Commands (EMRS)
8.2.2.1 Extend Mode Register Set Command (1), EMR (1)
( CS = "L", RAS = "L", CAS = "L", WE = "L", BA0 = "H", BA1 = "L", A0 to A12 = Register data)
The extended mode register (1) stores the data for enabling or disabling the DLL, output driver
strength, additive latency, ODT, DQS disable, OCD program. The default value of the extended
mode register (1) is not defined, therefore the extended mode register (1) must be programmed during
initialization for proper operation. The DDR2 SDRAM should be in all bank precharge with CKE
already high prior to writing into the extended mode register (1). The mode register set command
cycle time (tMRD) must be satisfied to complete the write operation to the extended mode register (1).
Extended mode register (1) contents can be changed using the same command and clock cycle
requirements during normal operation as long as all banks are in the precharge state. A0 is used for
DLL enable or disable. A1 is used for enabling a reduced strength output driver. A[5:3] determines the
additive latency, A[9:7] are used for OCD control, A10 is used for DQS disable. A2 and A6 are used
for ODT setting.
- 11 -
Publication Release Date: Sep. 03, 2012
Revision A03

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet W9725G6KB.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
W9725G6KB4M x 4-BANKS x 16-BIT DDR2 SDRAMWinbond
Winbond

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar