|
|
Número de pieza | VND7040AJ | |
Descripción | Double channel high-side driver | |
Fabricantes | STMicroelectronics | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de VND7040AJ (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! VND7040AJ
Double channel high-side driver with MultiSense analog
feedback for automotive applications
Datasheet - production data
Features
Max transient supply voltage
Operating voltage range
Typ. on-state resistance (per Ch)
Current limitation (typ)
Standby current (max)
VCC 40 V
VCC 4 to 28 V
RON 40 mΩ
ILIMH 34 A
ISTBY 0.5 µA
• Automotive qualified
• General
− Double channel smart high-side driver
with MultiSense analog feedback
− Very low standby current
− Compatible with 3 V and 5 V CMOS
outputs
• MultiSense diagnostic functions
− Multiplexed analog feedback of: load
current with high precision proportional
current mirror, VCC supply voltage and
TCHIP device temperature
− Overload and short to ground (power
limitation) indication
− Thermal shutdown indication
− OFF-state open-load detection
− Output short to VCC detection
− Sense enable/disable
• Protections
− Undervoltage shutdown
− Overvoltage clamp
− Load current limitation
− Self limiting of fast thermal transients
− Configurable latch-off on
overtemperature or power limitation
with dedicated fault reset pin
− Loss of ground and loss of VCC
− Reverse battery with external
components
− Electrostatic discharge protection
Applications
• All types of Automotive resistive, inductive
and capacitive loads
• Specially intended for automotive signal
lamps (up to P27W or SAE1156 and R5W
paralleled or LED rear combinations)
Description
The device is a double channel high-side driver
manufactured using ST proprietary VIPower® M0-
7 technology and housed in PowerSSO-16
package. The device is designed to drive 12 V
automotive grounded loads through a 3 V and
5 V CMOS-compatible interface, providing
protection and diagnostics.
The device integrates advanced protective
functions such as load current limitation, overload
active management by power limitation and
overtemperature shutdown with configurable
latch-off.
A FaultRST pin unlatches the output in case of
fault or disables the latch-off functionality.
A dedicated multifunction multiplexed analog
output pin delivers sophisticated diagnostic
functions including high precision proportional
load current sense, supply voltage feedback and
chip temperature sense, in addition to the
detection of overload and short circuit to ground,
short to VCC and OFF-state open-load.
A sense enable pin allows OFF-state diagnosis to
be disabled during the module low-power mode
as well as external sense resistor sharing among
similar devices.
May 2015
DocID027395 Rev 1
This is information on a product in full production.
1/46
www.st.com
1 page VND7040AJ
Block diagram and pin description
1 Block diagram and pin description
Figure 1: Block diagram
Name
Table 1: Pin functions
Function
VCC Battery connection.
OUTPUT0,1 Power output.
GND
Ground connection. Must be reverse battery protected by an external diode / resistor
network.
INPUT0,1
Voltage controlled input pin with hysteresis, compatible with 3 V and 5 V CMOS outputs.
It controls output switch state.
MultiSense
Multiplexed analog sense output pin; it delivers a current proportional to the selected
diagnostic: load current, supply voltage or chip temperature.
SEn
Active high compatible with 3 V and 5 V CMOS outputs pin; it enables the MultiSense
diagnostic pin.
SEL0,1
Active high compatible with 3 V and 5 V CMOS outputs pin; they address the MultiSense
multiplexer.
FaultRST
Active low compatible with 3 V and 5 V CMOS outputs pin; it unlatches the output in
case of fault; If kept low, sets the outputs in auto-restart. mode
DocID027395 Rev 1
5/46
5 Page VND7040AJ
7 V < VCC < 18 V; -40°C < Tj < 150°C
Table 8: Protections
Symbol
Parameter
Test conditions
ILIMH DC short circuit current
ILIML
TTSD
TR
TRS
Short circuit current
during thermal cycling
Shutdown temperature
Reset temperature(1)
Thermal reset of fault
diagnostic indication
VCC = 13 V
4 V < VCC < 18 V (1)
VCC = 13 V;
TR < Tj < TTSD
VFR = 0 V; VSEn = 5 V
THYST
ΔTJ_SD
Thermal hysteresis
(TTSD - TR)(1)
Dynamic temperature
tLATCH_RST
Fault reset time for output
unlatch(1)
VDEMAG
Turn-off output voltage
clamp
Output voltage drop
VON limitation
Tj = -40°C; VCC = 13 V
VFR = 5 V to 0 V;
VSEn = 5 V;
• E.g. Ch0:
VIN0 = 5 V;
VSEL0 = 0 V;
VSEL1 = 0 V
IOUT = 2 A; L = 6 mH;
Tj = -40°C
IOUT = 2 A; L = 6 mH;
Tj = 25°C to 150°C
IOUT = 0.25 A
Electrical specification
Min.
24
Typ.
34
13
Max. Unit
48
A
150 175
TRS + 1 TRS + 7
200
135 °C
7
60 K
3 10 20 µs
VCC - 38
V
VCC - 41 VCC - 46 VCC - 52 V
20 mV
Notes:
(1)Parameter guaranteed by design and characterization; not subject to production test.
Table 9: MultiSense
7 V < VCC < 18 V; -40°C < Tj < 150°C
Symbol
Parameter
VSENSE_CL
MultiSense clamp
voltage
Test conditions
VSEn = 0 V; ISENSE = 1 mA
VSEn = 0 V; ISENSE = -1 mA
Current sense characteristics
KOL
IOUT/ISENSE
IOUT = 0.01 A; VSENSE = 0.5 V;
VSEn = 5 V
dKcal/Kcal(1)(2)
Current sense ratio drift
at calibration point
IOUT = 0.01 A to 0.05 A;
Ical = 30 mA; VSENSE = 0.5 V;
VSEn = 5 V
KLED
IOUT/ISENSE
IOUT = 0.05 A; VSENSE = 0.5 V;
VSEn = 5 V
dKLED/KLED(1)(2) Current sense ratio drift
IOUT = 0.05 A; VSENSE = 0.5 V;
VSEn = 5 V
Min.
-17
Typ. Max. Unit
-12
V
7
530
-30 30 %
900 1700 2650
-25 25 %
DocID027395 Rev 1
11/46
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet VND7040AJ.PDF ] |
Número de pieza | Descripción | Fabricantes |
VND7040AJ | Double channel high-side driver | STMicroelectronics |
VND7040AJ-E | Double channel high-side driver | STMicroelectronics |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |