DataSheet.es    


PDF VN7007ALH Data sheet ( Hoja de datos )

Número de pieza VN7007ALH
Descripción high-side driver
Fabricantes STMicroelectronics 
Logotipo STMicroelectronics Logotipo



Hay una vista previa y un enlace de descarga de VN7007ALH (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! VN7007ALH Hoja de datos, Descripción, Manual

VN7007ALH
High-side driver with CurrentSense analog feedback for
automotive applications
Datasheet - production data
Features
Max transient supply voltage
Operating voltage range
Typ. on-state resistance (per Ch)
Current limitation (typ)
Stand-by current (max)
VCC 40 V
VCC 4 to 28 V
RON 7
ILIMH 100 A
ISTBY 0.5 µA
Automotive qualified
General
Single channel smart high-side driver
with CurrentSense analog feedback
Very low standby current
Compatible with 3 V and 5 V CMOS
outputs
Diagnostic functions
Overload and short to ground (power
limitation) indication
Thermal shutdown indication
OFF-state open-load detection
Output short to VCC detection
Sense enable/ disable
Protections
Undervoltage shutdown
Overvoltage clamp
Load current limitation
Self limiting of fast thermal transients
Loss of ground and loss of VCC
Configurable latch-off on
overtemperature or power limitation
Reverse battery
Electrostatic discharge protection
Applications
All types of Automotive resistive, inductive
and capacitive loads
Specially intended for Automotive
Headlamps
Description
The device is a single channel high-side driver
manufactured using ST proprietary VIPower®
technology and housed in the Octapak package.
The device is designed to drive 12 V automotive
grounded loads through a 3 V and 5 V CMOS-
compatible interface, and to provide protection
and diagnostics.
The device integrates advanced protective
functions such as load current limitation, overload
active management by power limitation and
overtemperature shutdown.
A combination of INPUT and FR_DIAG pins
latches the output in case of fault, disables the
latch-off functionality and enables OFF-state
diagnostic.
Table 1: Device summary
Package
Order codes
Tape and reel
Octapak
VN7007ALHTR
June 2015
DocID027958 Rev 1
This is information on a product in full production.
1/37
www.st.com

1 page




VN7007ALH pdf
VN7007ALH
Block diagram and pin description
1 Block diagram and pin description
Figure 1: Block diagram
Name
VCC
OUTPUT
GND
INPUT
CS
FR_DIAG
Table 2: Pin functions
Function
Battery connection.
Power outputs. All the pins must be connected together.
Ground connection.
Voltage controlled input pin with hysteresis. Compatible with 3 V and 5 V CMOS
outputs. It controls output switch state.
Analog current sense output pin delivers a current proportional to the load current.
It sets auto-restart and latch-off protection. Moreover, it enables OFF-state diagnostic
(see Table 12: "FR_DIAG functionality").
DocID027958 Rev 1
5/37

5 Page





VN7007ALH arduino
VN7007ALH
7 V < VCC < 18 V; -40°C < Tj < 150°C
Symbol
Parameter
VON
Output voltage drop
limitation
Test conditions
IOUT = 1.2 A
Electrical specification
Min.
Typ.
20
Max. Unit
mV
Notes:
(1)Parameter guaranteed by an indirect test sequence.
(2)Parameter guaranteed by design and characterization; not subject to production test.
Table 10: Current Sense
7 V < VCC < 18 V; -40°C < Tj < 150°C
Symbol
Parameter
Test conditions
Min. Typ. Max. Unit
VSENSE_CL CurrentSense clamp voltage
VFR_DIAG = 0 V; ISENSE = 1 mA
VFR_DIAG = 0 V;
ISENSE = -1 mA
-17 -12 V
7V
Current Sense characteristics
KOL1
IOUT/ISENSE
IOUT = 10 mA; VSENSE = 0.5 V;
VSEn = 5 V
800
KOL2
IOUT/ISENSE
IOUT = 0.25 A; VSENSE = 0.5 V;
VSEn = 5 V
10400
K0 IOUT/ISENSE
IOUT = 1 A; VSENSE = 4 V;
VSEn = 5 V
3390 6600 10180
dK0/K0(1)(2) Current sense ratio drift
IOUT = 1 A; VSENSE = 4 V;
-25
25 %
VSEn = 5 V
K1 IOUT/ISENSE
IOUT = 4.6 A; VSENSE = 4 V;
VSEn = 5 V
4080 6570 9530
dK1/K1(1)(2) Current sense ratio drift
IOUT = 4.6 A; VSENSE = 4 V;
VSEn = 5 V
-20
20 %
K2 IOUT/ISENSE
IOUT = 9 A; VSENSE = 4 V;
VSEn = 5 V
4830 6350 8060
dK2/K2(1)(2) Current sense ratio drift
IOUT = 9 A; VSENSE = 4 V;
VSEn = 5 V
-13
13 %
K3 IOUT/ISENSE
IOUT = 27 A; VSENSE = 4 V;
VSEn = 5 V
5600 6300 7150
dK3/K3(1)(2) Current sense ratio drift
IOUT = 27 A; VSENSE = 4 V;
VSEn = 5 V
-8
8%
CurrentSense disabled:
VFR_DIAG = 0 V
0 0.5 µA
CurrentSense disabled:
ISENSE0 CurrentSense leakage current -1 V < VSENSE < 5 V(1)
-0.5 0.5 µA
CurrentSense enabled:
VFR_DIAG = 5 V; VIN = 5 V;
IOUT = 0 A
0
2 µA
VOUT_CSD(1)
Output Voltage for
CurrentSense shutdown
VFR_DIAG = 5 V; RSENSE = 2.7 kΩ;
VIN = 5 V; IOUT = 3 A
5
V
DocID027958 Rev 1
11/37

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet VN7007ALH.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
VN7007ALHhigh-side driverSTMicroelectronics
STMicroelectronics

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar