DataSheet.es    

PDF VPS2535H Datasheet ( Hoja de datos )

Número de pieza VPS2535H
Descripción Double channel high-side driver
Fabricantes STMicroelectronics 
Logotipo STMicroelectronics Logotipo

Total 30 Páginas
		
VPS2535H Hoja de datos, Descripción, Manual
VPS2535H
Double channel high-side driver with analog current sense
0OWER33/ 
("1($'5
Features
Max transient supply voltage
Operating voltage range
Typ on-state resistance (per ch.)
Current limitation (typ)
Off-state supply current
VCC
VCC
RON
ILIM
IS
58 V
8 to 36 V
35 mΩ
42 A
2 µA
General
– Very low standby current
– 3.0 V CMOS compatible input
– Optimized electromagnetic emission
– Very low electromagnetic susceptibility
– Fault reset standby pin (FR_Stby)
Diagnostic functions
– Proportional load current sense
– High current sense precision for wide range
currents
– Off-state open load detection
– Output short to VCC detection
– Overload and short to ground latch off
– Thermal shutdown latch-off
– Very low current sense leakage
Protections
– Undervoltage shutdown
– Overvoltage clamp
– Load current limitation
– Self limiting of fast thermal transients
Datasheet production data
– Protection against loss of ground and loss
of VCC
– Thermal shutdown
– Electrostatic discharge protection
Application
All types of resistive, inductive and capacitive
loads
Description
The VPS2535H is a monolithic device made
using STMicroelectronics® VIPower® technology,
intended for driving resistive or inductive loads
with one side connected to ground. Active VCC
pin voltage clamp protects the device against low
energy spikes.
The device integrates an analog current sense
which delivers a current proportional to the load
current.
Fault conditions such as overload,
overtemperature or short to VCC are reported via
the current sense pin.
Output current limitation protects the device in
overload conditions. The device latches off in
case of overload or thermal shutdown.
The device is reset by a low level pass on the fault
reset standby pin.
A permanent low level on the inputs and on the
fault reset standby pins disables all outputs and
sets the device in standby mode.
January 2016
This is information on a product in full production.
DocID028862 Rev 1
1/30
www.st.com

1 page

VPS2535H pdf
VPS2535H
Block diagram and pin description
1 Block diagram and pin description
Figure 1. Block diagram
Signal Clamp
Undervoltage
IN1
IN2
FR_Stby
CS1
CS2
LOGIC
Control & Diagnostic 2
Control & Diagnostic 1
Power
Clamp
DRIVER
Over
Temperature
Current
Limitation
VON
Limitation
VSENSEH
OFF-state
Open-load
Current
Sense
OVERLOAD PROTECTION
(ACTIVE POWER LIMITATION)
VCC
CH1
CH2
OUT2
OUT1
GND
GAPGCFT00643
Name
VCC
OUT1,2
GND
IN1,2
CS1,2
FR_Stby
Table 1. Pin function
Function
Bus voltage connection
Power outputs
Ground connection
Voltage controlled input pins with hysteresis, CMOS compatible. They Control
output switch state
Analog current sense pins, they deliver a current proportional to the load current
In case of latch-off for overtemperature/overcurrent condition, a low pulse on the
FR_Stby pin is needed to reset the channel.
The device enters in standby mode if all inputs and the FR_Stby pin are low.
DocID028862 Rev 1
5/30
29

5 Page

VPS2535H arduino
VPS2535H
)5B6WGE\
Figure 5. TSTBY definition
Electrical specifications
,1387Q
,*1'
WVWE\
WVWE\
*$3*&)7
Table 8. Protections and diagnostics
Symbol
Parameter
Test conditions
Min. Typ. Max. Unit
VCC = 24 V
IlimH DC short circuit current
5 V < VCC < 36 V
30 42 55 A
55 A
IlimL
Short circuit current
during thermal cycling
VCC = 24 V; TR < Tj < TTSD
10.5
A
TTSD Shutdown temperature
TR Reset temperature
TRS Thermal reset of status
THYST
Thermal hysteresis
(TTSD-TR)
VDEMAG
Turn-off output voltage
clamp
IOUT = 3 A; VIN = 0;
L = 6 mH
150 175
TRS + 1 TRS + 5
135
7
200
°C
°C
°C
°C
VCC - 58 VCC - 64 VCC - 70 V
VON
Output voltage drop
limitation
IOUT = 150 mA;
Tj = -40 °C to 150 °C
25 mV
DocID028862 Rev 1
11/30
29

11 Page


PáginasTotal 30 Páginas
PDF Descargar[ VPS2535H.PDF ]

Enlace url


Hoja de datos destacado

Número de piezaDescripciónFabricantes
VPS2535HDouble channel high-side driverSTMicroelectronics
STMicroelectronics

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


www.DataSheet.es    |   2019   |  Privacy Policy  |  Contacto  |  Buscar