DataSheet.es    

PDF FS-V21X Datasheet ( Hoja de datos )

Número de pieza FS-V21X
Descripción DUAL DIGITAL FIBER SENSOR
Fabricantes Keyence 
Logotipo Keyence Logotipo

Total 4 Páginas
		
FS-V21X Hoja de datos, Descripción, Manual
96?M?0?746
DUAL DIGITAL FIBER
SENSOR
FS-V21/21G/21R(P)/21X
Instruction Manual
3. Mounting Unit
G DIN Track Mounting
1) As shown in the illustration, engage
the claw on the lower side of the
unit and the DIN rail, press the unit
in the direction shown by arrow ,
and move down the unit in the di-
rection shown by arrow .
2) When dismounting the unit, press
the unit in the direction shown by
arrow and move up the unit in
the direction shown by arrow .
G Using Mounting Bracket (accessory)
• Attach the unit to the mounting
bracket, mount them together, and
secure them with two M3 screws
as shown in the illustration.
1. Safety Precautions
WARNING
• This product is used to detect targets. Do not apply the product to
safety circuits for human protection.
• This product is not of explosion-proof construction. Do not use the
products in places with flammable gas, liquid, or dust.
• This product is a sensor of DC power supply type. Do not apply AC
power. The product may explode or burn if 100 VAC or a higher volt-
age is applied.
Check that all the accessories are ready before use.
• Accessories
Instruction manual (x 1)
Mounting bracket (x 1)
2. Part Names
Fiber lock lever
Operation indicator*
Digital monitor
Preset value (PV)
green indicator
Current value (CV)
red indicator
Dust cover
Set button
Manual button
Mode button
Expansion
protective cover
Expansion
connector
Output selector
Cable
* The operation indicator of the FS-V21X (infrared model) will not be lit.
4. Connecting Fiber Unit
Fiber insertion sign
1) Open the dust cover in the di-
rection shown by arrow .
2) Move down the fiber lock lever
in the direction shown by arrow
.
3) Insert a fiber unit into the fiber
insertion holes to a length of the
fiber insertion sign (i.e., approxi-
mately 14 mm).
4) Move up and return the fiber
lock lever in the direction shown
by the arrow .
Note:If a thin fiber unit is used, an adapter provided with the thin fiber unit
will be required.
Unless the right adapter is connected, the thin fiber unit will not
detect targets correctly.
Cable outer dia. Adapter
ø1.3
Adapter A
Appearance
ø1.0
Adapter B
• To connect the coaxial reflective type fiber unit to the amplifier, connect
the single-core fiber to the transmitter side, and connect the multiple-
core fiber to the receiver side.
Single-core fiber
Multi-core fiber
Transmitter
Receiver
5. I/O Cricuit
Refer to the following I/O circuit diagram when connecting the unit to pe-
ripheral devices.
G FS-V21/21G/21R/21X
G FS-V21RP
Brown Max. 100mA
Black
Load
Control output
12 to 24 VDC
5 to 40 VDC
Blue
0 VDC
Brown
12 to 24 VDC
Black Max. 100mA
Load
Control output
Blue
0 VDC
1

1 page


PáginasTotal 4 Páginas
PDF Descargar[ FS-V21X.PDF ]

Enlace url


Hoja de datos destacado

Número de piezaDescripciónFabricantes
FS-V21DUAL DIGITAL FIBER SENSORKeyence
Keyence
FS-V21GDUAL DIGITAL FIBER SENSORKeyence
Keyence
FS-V21RDUAL DIGITAL FIBER SENSORKeyence
Keyence
FS-V21RPDUAL DIGITAL FIBER SENSORKeyence
Keyence

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


www.DataSheet.es    |   2018   |  Privacy Policy  |  Contacto  |  Buscar