|
|
PDF V520H1-L03 Data sheet ( Hoja de datos )
| Número de pieza | V520H1-L03 | |
| Descripción | TFT LCD Module | |
| Fabricantes | CHI MEI | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de V520H1-L03 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
Issued Date: Feb.5.2007
Model No.: V520H1-L03
Approval
TFT LCD Approval Specification
MODEL NO.: V520H1 - L03
Customer:
Approved by:
Note:
Approved By
Reviewed By
Prepared By
TV Head Division
LY Chen
QRA Dept.
Tomy Chen
Product Development Div.
WT Lin
LCD TV Marketing and Product
Management Div.
Ken Wu
Keith Chen
1
The information described in this technical specification is tentative and it is possible to be changed without prior
notice. Please contact CMO ’s representative while your product design is based on this specification. Version 2.0
1 page  
Issued Date: Feb.5.2007
Model No.: V520H1-L03
Approval
1.5 MECHANICAL SPECIFICATIONS
Item
Horizontal (H)
Module Size Vertical (V)
Depth (D)
Min.
1235
718.2
56.5
Typ.
1236
719.2
57.5
Max.
1237
720.2
58.5
Unit Note
mm
mm
(1), (2)
mm W/I INV-COVER
Weight
21000
g-
Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.
Note (2) Module Depth does not include connectors.
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
Item
Storage Temperature
Operating Ambient Temperature
Shock (Non-Operating)
Vibration (Non-Operating)
Symbol
TST
TOP
SNOP
X, Y axis
Z axis
VNOP
Value
Min. Max.
-20 +60
0 50
- 40
- 30
- 1.0
Note (1) Temperature and relative humidity range is shown in the figure below.
Unit Note
ºC (1)
ºC (1), (2)
G (3), (5)
G (3), (5)
G (4), (5)
(a) 90 %RH Max. (Ta 40 ºC).
(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).
(c) No condensation.
Note (2) The maximum operating temperature is based on the test condition that the surface temperature of
display area is less than or equal to 65 ºC with LCD module alone in a temperature controlled
chamber. Thermal management should be considered in your product design to prevent the surface
temperature of display area from being over 65 ºC. The range of operating temperature may degrade
in case of improper thermal management in your product design.
Note (3) 11 ms, half sine wave, 1 time for ± X, ± Y, and ± Z.
Note (4) 10 ~ 200 Hz, 10 min, 1 time each X, Y, Z.
Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough so
that the module would not be twisted or bent by the fixture. The module would not be twisted or bent
by the fixture.
5
The information described in this technical specification is tentative and it is possible to be changed without prior
notice. Please contact CMO ’s representative while your product design is based on this specification. Version 2.0
5 Page 
Issued Date: Feb.5.2007
Model No.: V520H1-L03
Approval
3.2.3 INVERTER INTERTFACE CHARACTERISTICS
Parameter
On/Off Control Voltage ON
OFF
Internal/External PWM
Select Voltage
HI
LO
Internal PWM Control MAX
Voltage
MIN
External PWM Control HI
Voltage
LO
Control Signal Rising Time
Control Signal Falling Time
PWM Signal Rising Time
PWM Signal Falling Time
Input impedance
BLON Delay Time
BLON Off Time
Symbol
Test
Condition
VBLON
VSEL
VIPWM
VSEL = L
VEPWM
Tr
Tf
TPWMR
TPWMF
RIN
Ton
Toff
VSEL = H
Min.
2.0
0
2.0
0
2.85
2.0
0
1
1
1
Value
Typ.
-
3.0
0
Max.
5.0
0.8
5.0
0.8
3.15
5.0
0.8
100
100
50
50
Unit Note
V
V
V
V
V maximum duty ratio
V minimum duty ratio
V duty on
V duty off
ms
ms
us
us
M
ms
ms
Note (1) The SEL signal should be valid before backlight turns on by BLON signal. It is inhibited to
change the internal/external PWM selection (SEL) during backlight turn on period.
Note (2) The power sequence and control signal timing are shown in the following figure.
Note (3) The power sequence and control signal timing must follow the figure below. For a certain reason,
the inverter has a possibility to be damaged with wrong power sequence and control signal
timing.
11
The information described in this technical specification is tentative and it is possible to be changed without prior
notice. Please contact CMO ’s representative while your product design is based on this specification. Version 2.0
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet V520H1-L03.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| V520H1-L01 | TFT LCD | CHI MEI |
| V520H1-L03 | TFT LCD Module | CHI MEI |
| V520H1-L04 | TFT LCD Module | CHI MEI |
| V520H1-L05 | TFT LCD Module |  CMI MEI |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |