DataSheet.es    


PDF R5F51116AGFK Data sheet ( Hoja de datos )

Número de pieza R5F51116AGFK
Descripción 32 MHz 32-bit RX MCUs
Fabricantes Renesas 
Logotipo Renesas Logotipo



Hay una vista previa y un enlace de descarga de R5F51116AGFK (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! R5F51116AGFK Hoja de datos, Descripción, Manual

Datasheet
RX111 Group
R01DS0190EJ0121
Renesas MCUs
Rev.1.21
32 MHz 32-bit RX MCUs, 50 DMIPS, up to 512 Kbytes of flash memory,
Dec 09, 2014
USB 2.0 full-speed host/function/OTG, up to 6 comms channels,
12-bit A/D, 8-bit D/A, RTC
Features
32-bit RX CPU core
32 MHz maximum operating frequency
Capable of 50 DMIPS when operating at 32 MHz
Accumulator handles 64-bit results (for a single
instruction) from 32-bit × 32-bit operations
Multiplication and division unit handles 32-bit × 32-bit
operations (multiplication instructions take one CPU
clock cycle)
Fast interrupt
CISC Harvard architecture with five-stage pipeline
Variable-length instruction format, ultra-compact code
On-chip debugging circuit
Low power consumption functions
Operation from a single 1.8 to 3.6 V supply
Three low power consumption modes
Supply current
High-speed operating mode: 0.11 mA/MHz
Software standby mode: 0.44 μA
Recovery time from software standby mode: 4.8 μs
On-chip flash memory for code, no wait states
Operation at 32 MHz, read cycle of 31.25 ns
No wait states for reading at full CPU speed
16 to 512 Kbyte capacities
Programmable at 1.8 V
For instructions and operands
On-chip data flash memory
8 Kbytes
1,000,000 Erase/Write cycles (typ.)
BGO (Background Operation)
On-chip SRAM, no wait states
8 to 64 Kbyte capacities
Data transfer controller (DTC)
Four transfer modes
Transfer can be set for each interrupt source.
Event link controller (ELC)
Module operation can be initiated by event signals without
going through interrupts.
Link operation between modules is possible while the
CPU is sleeping.
Reset and power supply voltage management
Six types including Power-On Reset (POR)
Low voltage detection (LVD) with voltage settings
Clock functions
External clock input frequency: Up to 20 MHz
Main clock oscillator frequency: 1 to 20 MHz
Sub-clock oscillator frequency: 32.768 kHz
PLL circuit input: 4 to 8 MHz
Low-speed on-chip oscillator: 4 MHz
High-speed on-chip oscillator: 32 MHz±1% (20 to 85°C)
IWDT-dedicated on-chip oscillator: 15 kHz
Generate a dedicated 32.768-kHz clock for the RTC
On-chip clock frequency accuracy measurement circuit
(CAC)
Realtime clock (RTC)
30-second, leap year, and error adjustment functions
Calendar count mode or binary count mode selectable
Capable of initiating exit from software standby mode
R01DS0190EJ0121 Rev.1.21
Dec 09, 2014
PLQP0064KB-A 10 × 10 mm, 0.5 mm pitch
PLQP0064GA-A 14 × 14 mm, 0.8 mm pitch
PLQP0048KB-A 7 × 7 mm, 0.5 mm pitch
PWQN0048KB-A 7 × 7 mm, 0.50 mm pitch
PWQN0040KC-A 6 × 6 mm, 0.50 mm pitch
PWLG0064KA-A 5 × 5 mm, 0.5 mm pitch
PWLG0036KA-A 4 × 4 mm, 0.5 mm pitch
Independent watchdog timer (IWDT)
15-kHz on-chip oscillator produces a dedicated clock
signal to drive IWDT operation.
On-chip functions for IEC 60730 compliance
Clock frequency accuracy measurement circuit, IWDT,
functions to assist in RAM testing, etc.
Up to six channels for communication
USB: USB 2.0 host (32 Kbyte or more ROM)/function/
On-The-Go (OTG) (one channel), full-speed = 12 Mbps,
low-speed = 1.5 Mbps, isochronous transfer, and BC
(Battery Charger) supported
SCI: Asynchronous mode, clock synchronous mode,
smart card interface (up to three channels)
I2C bus interface: Transfer at up to 400 kbps, capable of
SMBus operation (one channel)
RSPI: Up to 16 Mbps (one channel)
Up to 8 extended-function timers
16-bit MTU: Input capture/output compare,
complementary PWM output, phase counting mode
(six channels)
16-bit CMT (two channels)
12-bit A/D converter
Up to 14 channels
1.0 μs minimum conversion speed
Double trigger (data duplication) function for motor
control
8-bit D/A converter
Two channels (for 64 pins only)
Temperature sensor
General I/O ports
5-V tolerant, open drain, input pull-up
Multi-function pin controller (MPC)
Multiple I/O pins can be selected for peripheral functions.
Unique ID
32-byte ID code for the MCU
Operating temperature range
 40 to 85C
 40 to 105°C
Page 1 of 114

1 page




R5F51116AGFK pdf
RX111 Group
1. Overview
Table 1.2
Comparison of Functions for Different Packages
Module/Functions
Interrupts
External interrupts
DMA
Data transfer controller
Timers
Multi-function timer pulse unit 2
Port output enable 2
Compare match timer
Realtime clock
Independent watchdog timer
Communication Serial communications interfaces
functions
[simple I2C, simple SPI]
Serial communications interface
[simple I2C, simple SPI]
I2C bus interface
Serial peripheral interface
USB 2.0 host/function module
(USBc)
12-bit A/D converter
(including high-precision channels)
D/A converter
Temperature sensor
CRC calculator
Event link controller
Packages
RX111 Group
64 Pins
48 Pins
40 Pins
36 Pins
NMI, IRQ0 to IRQ7
Supported
6 channels (MTU0 to MTU5)
POE0# to POE3#, POE8#
POE0#, POE2#, POE3#, POE8#
2 channels × 1 unit
Supported
Not supported
Supported
2 channels (SCI1, SCI5)
1 channel (SCI12)
1 channel
1 channel
(Host/Function/
OTG)
14 channels
(6 channels)
2 channels
64-pin LFQFP
64-pin LQFP
64-pin WFLGA
1 channel
1 channel
1 channel
(SSLA1 and SSLA3 are not supported) (SSLA1 to SSLA3
are not supported)
1 channel
(Host/Function)
10 channels
(4 channels)
8 channels
(3 channels)
Not supported
Supported
Supported
Supported
48-pin LFQFP
48-pin HWQFN
40-pin HWQFN
7 channels
(2 channels)
36-pin WFLGA
R01DS0190EJ0121 Rev.1.21
Dec 09, 2014
Page 5 of 114

5 Page





R5F51116AGFK arduino
RX111 Group
1. Overview
Table 1.4
Pin Functions (2/3)
Classifications Pin Name
I/O Description
Serial
communications
interface (SCIe)
Simple I2C mode
SSCL1, SSCL5
SSDA1, SSDA5
I/O Input/output pins for the I2C clock.
I/O Input/output pins for the I2C data.
Simple SPI mode
SCK1, SCK5
I/O Input/output pins for the clock.
SMISO1, SMISO5
I/O Input/output pins for slave transmit data.
SMOSI1, SMOSI5
I/O Input/output pins for master transmit data.
SS1#, SS5#
Input Chip-select input pins.
Serial
communications
interface (SCIf)
Asynchronous mode/clock synchronous mode
SCK12
I/O Input/output pin for the clock.
RXD12
Input Input pin for receiving data.
TXD12
Output Output pin for transmitting data.
CTS12#
Input Input pin for controlling the start of transmission and reception.
RTS12#
Output Output pin for controlling the start of transmission and reception.
Simple I2C mode
SSCL12
I/O Input/output pin for the I2C clock.
SSDA12
I/O Input/output pin for the I2C data.
Simple SPI mode
SCK12
I/O Input/output pin for the clock.
SMISO12
I/O Input/output pin for slave transmit data.
SMOSI12
I/O Input/output pin for master transmit data.
SS12#
Input Chip-select input pin.
Extended serial mode
RXDX12
Input Input pin for data reception by SCIf.
TXDX12
Output Output pin for data transmission by SCIf.
SIOX12
I/O Input/output pin for data reception or transmission by SCIf.
I2C bus interface SCL0
I/O Input/output pin for I2C bus interface clocks. Bus can be directly driven by
the N-channel open drain output.
SDA0
I/O Input/output pin for I2C bus interface data. Bus can be directly driven by the
N-channel open drain output.
Serial peripheral RSPCKA
interface
MOSIA
I/O Input/output pin for the RSPI clock.
I/O Input/output pin for transmitting data from the RSPI master.
MISOA
I/O Input/output pin for transmitting data from the RSPI slave.
SSLA0
I/O Input/output pin to select the slave for the RSPI.
SSLA1 to SSLA3
Output Output pins to select the slave for the RSPI.
USB 2.0 host/ VCC_USB
function module VSS_USB
Input
Input
Power supply pin for USB. Connect this pin to VCC.
Ground pin for USB. Connect this pin to VSS.
USB0_DP
I/O D+ I/O pin of the USB on-chip transceiver.
USB0_DM
I/O D- I/O pin of the USB on-chip transceiver.
USB0_VBUS
Input USB cable connection monitor pin.
USB0_EXICEN
Output Low-power control signal for the OTG chip.
USB0_VBUSEN
Output VBUS (5 V) supply enable signal for the OTG chip.
USB0_OVRCURA,
USB0_OVRCURB
Input External overcurrent detection pins.
USB0_ID
Input Mini-AB connector ID input pin during operation in OTG mode.
R01DS0190EJ0121 Rev.1.21
Dec 09, 2014
Page 11 of 114

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet R5F51116AGFK.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
R5F51116AGFK32 MHz 32-bit RX MCUsRenesas
Renesas
R5F51116AGFL32 MHz 32-bit RX MCUsRenesas
Renesas
R5F51116AGFM32 MHz 32-bit RX MCUsRenesas
Renesas

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar