|
|
PDF CL2102-L Data sheet ( Hoja de datos )
| Número de pieza | CL2102-L | |
| Descripción | Low Noise Amplifier | |
| Fabricantes | RFHIC | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de CL2102-L (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
|
No Preview Available !
Low Noise Amplifier
Product Features
• GaAs p-HEMT chip on board
• No matching circuit needed
• High Maximum input power(+25dBm)
• High IP3 & Low Noise
• Single Supply Voltage (+5V)
• Surface Mount Hybrid Type
• Tape & Reel Packaging
• Small Size, High Heatsink
• Alumina Substrate
• Pb Free / RoHS Standard
CL0902-L / CL1502-L
CL1802-L / CL2102-L
Applications
• 2G & 3G Repeater
• Base Station
• PCS, CDMA, W-CDMA
• GSM, DCS, UMTS
• WiMAX, Wibro, WLAN
• RF Sub-Systems
Package Type : CP-16A
Description
RFHIC’s LOW Noise Amplifier series are all hybrid LNA type products which includes all matching for the convenience of customers.
CL series are focused on giving lowest noise possible. The structure of the device is built with GaAs p-HEMT die attached on a
ceramic thick film substrate. The device is still smaller than the area one would use for the application notes all together. Depending on
the part number, one can use this in different frequency applications. All LNA hybrids are possible to have custom frequency & spec
without any additional NRE cost involved. All RFHIC products are RoHS compliant.
Electrical Specifications
PARAMETER
UNIT
CL0902-L
Frequency Range
MHz
824 ~ 894
(Cellular)
890 ~ 960
(GSM)
Small Signal Gain (S21)
Gain Flatness
dB 21
dB ±0.5
20
±0.5
Input Return Loss (S11)
Output Return Loss (S22)
1dB Compression Point (P1dB)
Output 3rd Order Intercept Point
(OIP3) (TYP.)
dB
dB
dBm
dBm
-17
-8.5
20
31
-17
-8.5
20
31
Noise Figure (TYP.)
dB 0.7
0.7
DC Supply
Current (Vdc=+5V)
mA 100
100
Test Condition
① Supply voltage = +5V, 50ohm System, Ta = 25℃
② OIP3 is measured with two tones, at an output power of +0dBm/tone separated by 1MHz.
CL1502-L
1400 ~ 1600
17
±0.5
-17
-10
21
33
0.6
90
CL1802-L
1700 ~ 2000
16
±0.5
-18
-10
21
33
0.6
100
CL2102-L
1850 ~ 2200
15
±1.0
-18
-10
20
33
0.6
100
Korean Facilities : 82-31-250-5078 / [email protected]
US Facility : 919-677-8780 / [email protected]
1/6
All specifications may change without notice
Version 6.3
1 page  
Low Noise Amplifier
CL0902-L / CL1502-L
CL1802-L / CL2102-L
Package Dimensions (Type: CP-16A)
* Unit: mm[inch] | Tolerance ±0.15[.006]
Pin No
1
2
3
▲ Top View
▲ Side View
Pin Description
Function
Pin No
GND
4
Input
5
GND
6
▲ Bottom View
Function
GND
Output
Vcc
Recommended Pattern
Recommended Mounting Configuration
* Mounting Configuration Notes
1. Ground / thermal via holes are critical for the proper performance of this device.
2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance.
3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via hole region contacts the heatsink.
4. Do not put solder mask on the backside of the PCB in the region where the board contacts the heatsink.
5. RF trace width depends upon the PCB material and construction.
6. Use 1 oz. Copper minimum.
Korean Facilities : 82-31-250-5078 / [email protected]
US Facility : 919-677-8780 / [email protected]
5/6
All specifications may change without notice
Version 6.3
5 Page | ||
| Páginas | Total 6 Páginas | |
| PDF Descargar | [ Datasheet CL2102-L.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| CL2102-L | Low Noise Amplifier | RFHIC |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |