|
|
PDF OKY2-T-16-D12P-C Data sheet ( Hoja de datos )
| Número de pieza | OKY2-T-16-D12P-C | |
| Descripción | Programmable DOSA-SMT 10/16-Amp DC/DC Converters | |
| Fabricantes | Murata | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de OKY2-T-16-D12P-C (archivo pdf) en la parte inferior de esta página. Total 17 Páginas | ||
|
No Preview Available !
www.murata-ps.com
OKY-T/10 & T/16-D12 Series
Programmable DOSA-SMT 10/16-Amp DC/DC Converters
Typical unit
FEATURES
Wide 8.3-14 VDC input range
Non-isolated output adjustable from 0.7525 to
5.5 Volts up to 16 Amps
DOSA-compatible SMT package
Optional sequence/tracking operation
Outstanding thermal performance and derating
Short circuit protection
On/Off control
High efficiency up to 94.5%
Over temperature protection
Meets UL/EN/IEC 60950-1 safety approvals.
PRODUCT OVERVIEW
The OKY-T/10 and -T/16 series are miniature
SMT non-isolated Point-of-Load (POL) DC/DC power
converters for embedded applications. The module
is fully compatible with Distributed-power Open
Standards Alliance (DOSA) industry-standard
specifications (www.dosapower.com). Applications
include powering CPU’s, datacom/telecom systems,
programmable logic and mixed voltage systems.
The wide input range is 8.3 to 14 Volts DC. Two
maximum output currents are offered, 10 Amps
(T/10 models) or 16 Amps (T/16 models). Based
on fixed-frequency synchronous buck converter
switching topology, the high power conversion
efficient Point of Load (POL) module features pro-
grammable output voltage and On/Off control. An
optional Sequence/Tracking input allows controlled
ramp-up and ramp-down outputs. The Sense input
provides remote sense. These converters also
include under voltage lock out (UVLO), output short
circuit protection, over-current and over tempera-
ture protections.
These units are designed to meet all standard
UL/EN/IEC 60950-1 safety and FCC EMI/RFI
emissions certifications and RoHS-6 hazardous
substance compliance.
Contents
Description, Connection Diagram, Photograph
Ordering Guide, Model Numbering
Mechanical Specifications, Input/Output Pinout
Detailed Electrical Specifications
Output Voltage Adjustment, Soldering Guidelines
Application Notes
Performance Data – OKY2-T/10-D12
Performance Data and Oscillograms – OKY2-T/16-D12
Tape and Reel Information
Product Label, MTBF Table
Page
1
2
3
4
5
6
9
11
16
17
+Vin
F1
On/Off
Control
Controller
External
DC
Power
Source
Open = On
Closed = Off
(Positive
On/Off)
Common
Sequence/Tracking (OKY2 only)
Simplified Block Diagram
t4XJUDIJOH
t'JMUFST
t$VSSFOU4FOTF
Reference and
Error Amplifier
+Vout
Sense
Trim
Figure 1. OKY-T/10, -T/16
Common
Note: Murata Power Solutions strongly recommends an external input fuse, F1.
See specifications.
For full details go to
www.murata-ps.com/rohs
www.murata-ps.com/support
MDC_OKY_T10T16.D12.A08 Page 1 of 17
1 page  
OKY-T/10 & T/16-D12 Series
Programmable DOSA-SMT 10/16-Amp DC/DC Converters
Specification Notes, Cont.:
(5) The On/Off Control Input should use either a switch or an open collector/open drain transistor referenced to
-Input Common. A logic gate may also be used by applying appropriate external voltages which not exceed
+Vin.
(6) Short circuit shutdown begins when the output voltage degrades approximately 2% from the selected
setting.
(7) Deleted.
(8) Output noise may be further reduced by adding an external filter. At zero output current, the output may
contain low frequency components which exceed the ripple specification. The output may be operated
indefinitely with no load.
(9) All models are fully operational and meet published specifications, including “cold start” at –40°C.
(10) Regulation specifications describe the deviation as the line input voltage or output load current is varied
from a nominal midpoint value to either extreme.
(11) Other input or output voltage ranges will be reviewed under scheduled quantity special order.
(12) Maximum PC board temperature is measured with the sensor in the center of the converter.
(13) Do not exceed maximum power specifications when adjusting the output trim.
(14) The maximum output capacitive loads depend on the the Equivalent Series Resistance (ESR) of the external
output capacitor and, to a lesser extent, the distance and series impedance to the load. Larger caps will
reduce output noise but may change the transient response. Newer ceramic caps with very low ESR may
require lower capacitor values to avoid instability. Thoroughly test your capacitors in the application. Please
refer to the Output Capacitive Load Application Note.
(15) Do not allow the input voltage to degrade lower than the input undervoltage shutdown voltage at all times.
Otherwise, you risk having the converter turn off. The undervoltage shutdown is not latching and will
attempt to recover when the input is brought back into normal operating range.
(16) The output is not intended to sink appreciable reverse current.
(17) “Hiccup” overcurrent operation repeatedly attempts to restart the converter with a brief, full-current output.
If the overcurrent condition still exists, the restart current will be removed and then tried again. This short
current pulse prevents overheating and damaging the converter. Once the fault is removed, the converter
immediately recovers normal operation.
Output Voltage Adjustment
The output voltage may be adjusted over a limited range by connect-
ing an external trim resistor (Rtrim) between the Trim pin and Ground. The
Rtrim resistor must be a 1/10 Watt precision metal film type, ±1% accuracy
or better with low temperature coefficient, ±100 ppm/°C. or better. Mount
the resistor close to the converter with very short leads or use a surface
mount trim resistor.
In the tables opposite, the calculated resistance is given. Do not exceed
the specified limits of the output voltage or the converter’s maximum power
rating when applying these resistors. Also, avoid high noise at the Trim
input. However, to prevent instability, you should never connect any capaci-
tors to Trim.
OKY2-T/10-D12, -T/16-D12
Output Voltage
5.0 V.
3.3 V.
2.5 V.
2.0 V.
1.8 V.
1.5 V.
1.2 V.
1.0 V.
0.7525 V.
Calculated Rtrim (KΩ)
1.472
3.122
5.009
7.416
9.024
13.05
22.46
41.424
∞ (open)
Resistor Trim Equation, D12 models:
RTRIM () = _____1_0_5_0_0____ –1000
VOUT – 0.7525V
Soldering Guidelines
Murata Power Solutions recommends the specifications below when installing these
converters. These specifications vary depending on the solder type. Exceeding these
specifications may cause damage to the product. Your production environment
may differ therefore please thoroughly review these guidelines with your process
engineers.
Reflow Solder Operations for surface-mount products (SMT)
For Sn/Ag/Cu based solders:
Preheat Temperature
Less than 1 ºC. per second
Time over Liquidus
45 to 75 seconds
Maximum Peak Temperature 260 ºC.
Cooling Rate
Less than 3 ºC. per second
For Sn/Pb based solders:
Preheat Temperature
Less than 1 ºC. per second
Time over Liquidus
60 to 75 seconds
Maximum Peak Temperature 235 ºC.
Cooling Rate
Less than 3 ºC. per second
Recommended Lead-free Solder Reflow Profile
250
Peak Temp.
235-260° C
200
150 Reflow Zone
Soaking Zone
time above 217° C
120 sec max
45-75 sec
100
<1.5° C/sec
Preheating Zone
50
240 sec max
High trace = normal upper limit
Low trace = normal lower limit
0
0 30 60 90 120 150 180 210 240 270 300
Time (sec)
High trace = normal upper limit
Low trace - normal lower limit
www.murata-ps.com/support
MDC_OKY_T10T16.D12.A08 Page 5 of 17
5 Page 
OKY-T/10 & T/16-D12 Series
Programmable DOSA-SMT 10/16-Amp DC/DC Converters
PERFORMANCE DATA AND OSCILLOGRAMS – OKY2-T/16-D12
OKY2-T/16-D12 Efficiency vs. Line Voltage and Load Current @ +25°C
(VOUT = 0.7525V)
84
OKY2-T/16-D12-C Maximum Current Temperature Derating at Sea Level
(VIN= 12V, VOUT = 0.75V).
17
79 16
74 VIN = 8.3V
VIN = 12V
VIN = 14V
69
64
59
54
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Load Curre nt (Amps)
15
Natural convection
14 100 LFM
200 LFM
300 LFM
13 400 LFM
12
11
10
20 25 30 35 40 45 50 55 60 65 70 75 80 85 90
Ambient Temperature (ºC)
OKY2-T/16-D12 Efficiency vs. Line Voltage and Load Current @ +25°C
(VOUT = 1V)
85
80
VIN = 8.3V
VIN = 12V
75 VIN = 14V
70
65
OKY2-T/16-D12 Efficiency vs. Line Voltage and Load Current @ +25°C
(VOUT = 1.2)
85
80 VIN = 8.3V
VIN = 12V
VIN = 14V
75
70
60
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Load Curre nt (Amps)
65
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Load Curre nt (Amps)
OKY2-T/16-D12 Efficiency vs. Line Voltage and Load Current @ +25°C
(VOUT = 1.5V)
86
VIN = 8.3V
81 VIN = 12V
VIN = 14V
76
71
66
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Load Curre nt (Amps)
www.murata-ps.com/support
MDC_OKY_T10T16.D12.A08 Page 11 of 17
11 Page | ||
| Páginas | Total 17 Páginas | |
| PDF Descargar | [ Datasheet OKY2-T-16-D12P-C.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| OKY2-T-16-D12P-C | Programmable DOSA-SMT 10/16-Amp DC/DC Converters | Murata |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |