DataSheet.es    


PDF 28HC256 Data sheet ( Hoja de datos )

Número de pieza 28HC256
Descripción AT28HC256
Fabricantes ATMEL Corporation 
Logotipo ATMEL Corporation Logotipo



Hay una vista previa y un enlace de descarga de 28HC256 (archivo pdf) en la parte inferior de esta página.


Total 24 Páginas

No Preview Available ! 28HC256 Hoja de datos, Descripción, Manual

Features
Fast Read Access Time – 70 ns
Automatic Page Write Operation
– Internal Address and Data Latches for 64 Bytes
– Internal Control Timer
Fast Write Cycle Times
– Page Write Cycle Time: 3 ms or 10 ms Maximum
– 1 to 64-byte Page Write Operation
Low Power Dissipation
– 80 mA Active Current
– 3 mA Standby Current
Hardware and Software Data Protection
DATA Polling for End of Write Detection
High Reliability CMOS Technology
– Endurance: 104 or 105 Cycles
– Data Retention: 10 Years
Single 5V ± 10% Supply
CMOS and TTL Compatible Inputs and Outputs
JEDEC Approved Byte-wide Pinout
Full Military and Industrial Temperature Ranges
Green (Pb/Halide-free) Packaging Option
256K (32K x 8)
High-speed
Parallel
EEPROM
AT28HC256
1. Description
The AT28HC256 is a high-performance electrically erasable and programmable read-
only memory. Its 256K of memory is organized as 32,768 words by 8 bits. Manufac-
tured with Atmel’s advanced nonvolatile CMOS technology, the AT28HC256 offers
access times to 70 ns with power dissipation of just 440 mW. When the AT28HC256
is deselected, the standby current is less than 5 mA.
The AT28HC256 is accessed like a Static RAM for the read or write cycle without the
need for external components. The device contains a 64-byte page register to allow
writing of up to 64 bytes simultaneously. During a write cycle, the address and 1 to 64
bytes of data are internally latched, freeing the addresses and data bus for other oper-
ations. Following the initiation of a write cycle, the device will automatically write the
latched data using an internal control timer. The end of a write cycle can be detected
by DATA Polling of I/O7. Once the end of a write cycle has been detected a new
access for a read or write can begin.
Atmel’s 28HC256 has additional features to ensure high quality and manufacturability.
The device utilizes internal error correction for extended endurance and improved
data retention characteristics. An optional software data protection mechanism is
available to guard against inadvertent writes. The device also includes an extra
64 bytes of EEPROM for device identification or tracking.
0007N–PEEPR–9/09

1 page




28HC256 pdf
AT28HC256
5. DC and AC Operating Range
Operating
Temperature (Case)
VCC Power Supply
Ind.
Mil.
AT28HC256-70
-40°C - 85°C
5V ± 10%
AT28HC256-90
-40°C - 85°C
-55°C - 125°C
5V ± 10%
AT28HC256-12
-40°C - 85°C
-55°C - 125°C
5V ± 10%
6. Operating Modes
Mode
CE
Read
Write(2)
Standby/Write Inhibit
Write Inhibit
VIL
VIL
VIH
X
Write Inhibit
X
Output Disable
X
Chip Erase
Notes: 1. X can be VIL or VIH.
2. Refer to AC programming waveforms.
VIL
3. VH = 12.0V ± 0.5V.
7. Absolute Maximum Ratings*
Temperature under Bias ................................ -55°C to +125°C
Storage Temperature ..................................... -65°C to +150°C
All Input Voltages
(including NC Pins)
with Respect to Ground ...................................-0.6V to +6.25V
All Output Voltages
with Respect to Ground .............................-0.6V to VCC + 0.6V
Voltage on OE and A9
with Respect to Ground ...................................-0.6V to +13.5V
OE
VIL
VIH
X(1)
X
VIL
VIH
VH(3)
WE I/O
VIH DOUT
VIL DIN
X High Z
VIH
X
X High Z
VIL High Z
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability
8. DC Characteristics
Symbol
ILI
ILO
Parameter
Input Load Current
Output Leakage Current
ISB1 VCC Standby Current TTL
ISB2 VCC Standby Current CMOS
ICC VCC Active Current
VIL Input Low Voltage
VIH Input High Voltage
VOL Output Low Voltage
VOH Output High Voltage
Condition
VIN = 0V to VCC + 1V
VI/O = 0V to VCC
CE = 2.0V to VCC
CE = VCC - 0.3V to VCC
f = 5 MHz; IOUT = 0 mA
IOL = 6.0 mA
IOH = -4 mA
AT28HC256-90, -12
AT28HC256-70
AT28HC256-90, -12
Min
2.0
2.4
Max Units
10 µA
10 µA
3 mA
60 mA
300 µA
80 mA
0.8 V
V
0.45 V
V
0007N–PEEPR–9/09
5

5 Page





28HC256 arduino
22. Data Polling Characteristics(1)
Symbol Parameter
tDH
tOEH
tOE
tWR
Notes:
Data Hold Time
OE Hold Time
OE to Output Delay(2)
Write Recovery Time
1. These parameters are characterized and not 100% tested.
2. See “AC Read Characteristics” on page 6.
23. Data Polling Waveforms
AT28HC256
Min Typ Max Units
0 ns
0 ns
ns
0 ns
24. Toggle Bit Characteristics(1)
Symbol Parameter
tDH
tOEH
tOE
tOEHP
tWR
Notes:
Data Hold Time
OE Hold Time
OE to Output Delay(2)
OE High Pulse
Write Recovery Time
1. These parameters are characterized and not 100% tested.
2. See “AC Read Characteristics” on page 6.
25. Toggle Bit Waveforms
Min Typ Max Units
10 ns
10 ns
ns
150 ns
0 ns
Notes:
1. Toggling either OE or CE or both OE and CE will operate toggle bit.
2. Beginning and ending state of I/O6 will vary.
3. Any address location may be used but the address should not vary.
0007N–PEEPR–9/09
11

11 Page







PáginasTotal 24 Páginas
PDF Descargar[ Datasheet 28HC256.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
28HC256AT28HC256ATMEL Corporation
ATMEL Corporation

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar