|
|
PDF LCB710S Data sheet ( Hoja de datos )
| Número de pieza | LCB710S | |
| Descripción | Single-Pole Normally Closed OptoMOS Relay | |
| Fabricantes | IXYS | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LCB710S (archivo pdf) en la parte inferior de esta página. Total 7 Páginas | ||
|
No Preview Available !
INTEGRATED CIRCUITS DIVISION
Parameter
Load Voltage
Load Current
On-Resistance (max)
LED Current to Operate
Rating
60
1
0.6
2
Units
VP
Arms / ADC
mA
Features
• 1A Load Current
• 0.6 Max On-Resistance
• 2mA Control Current
• 3750Vrms Input/Output Isolation
• Low Drive Power Requirements (TTL/CMOS
Compatible)
• No Moving Parts
• High Reliability
• Arc-Free With No Snubbing Circuits
• No EMI/RFI Generation
• Machine Insertable, Wave Solderable
• Small 6-Pin Package
• Tape & Reel, Surface Mount Version Available
Applications
• Sensor Circuitry
• Instrumentation
• Multiplexers
• Data Acquisition
• Electronic Switching
• I/O Subsystems
• Meters (gas, oil, electric and water)
• Medical Equipment-Patient/Equipment Isolation
• Security
• Aerospace
• Industrial Controls
LCB710
Single-Pole, Normally Closed
OptoMOS® Relay
Description
LCB710 is a single-pole normally closed
(1-Form-B) solid state relay that uses optically
coupled technology to provide an enhanced 3750Vrms
isolation barrier between the input and the output of
the relay. The efficient MOSFET switches use IXYS
Integrated Circuits Division's patented OptoMOS
architecture. The optically coupled output is controlled
by a highly efficient GaAlAs infrared LED.
Approvals
• UL Recognized Component: File E76270
• CSA Certified Component: Certificate 1175739
• EN/IEC 60950-1 Certified Component:
TUV Certificate B 09 07 49410 004
Ordering Information
Part #
LCB710
LCB710S
LCB710STR
Description
6-Lead DIP (50/Tube)
6-Lead Surface Mount (50/Tube)
6-Lead Surface Mount (1000/Reel)
Pin Configuration
AC/DC Configuration
1
+ Control
2
– Control
3
Do Not Use
6
Load
5
Do Not Use
4
Load
DC Only Configuration
1
+ Control
2
– Control
3
Do Not Use
6
5
4
+ Load
– Load
Pb
DS-LCB710-R02
e3
Switching Characteristics
of Normally Closed Devices
Form-B
IF
ILOAD
10%
toff
90%
ton
www.ixysic.com
1
1 page  
INTEGRATED CIRCUITS DIVISION
LCB710
Manufacturing Information
Moisture Sensitivity
All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated
Circuits Division classified all of its plastic encapsulated devices for moisture sensitivity according to
the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product
evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper
operation of our devices when handled according to the limitations and information in that standard as well as to any
limitations set forth in the information or standards referenced below.
Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced
product performance, reduction of operable life, and/or reduction of overall reliability.
This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according
to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033.
Device
LCB710 / LCB710S
Moisture Sensitivity Level (MSL) Rating
MSL 1
ESD Sensitivity
This product is ESD Sensitive, and should be handled according to the industry standard JESD-625.
Reflow Profile
This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020
must be observed.
Device
LCB710 / LCB710S
Maximum Temperature x Time
250ºC for 30 seconds
Board Wash
IXYS Integrated Circuits Division recommends the use of no-clean flux formulations. However, board washing to
remove flux residue is acceptable. Since IXYS Integrated Circuits Division employs the use of silicone coating as
an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary
if a wash is used after solder reflow processes. Chlorine- or Fluorine-based solvents or fluxes should not be used.
Cleaning methods that employ ultrasonic energy should not be used.
Pb e3
R02 www.ixysic.com
5
5 Page | ||
| Páginas | Total 7 Páginas | |
| PDF Descargar | [ Datasheet LCB710S.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LCB710 | Single-Pole Normally Closed OptoMOS Relay | IXYS |
| LCB710S | Single-Pole Normally Closed OptoMOS Relay | IXYS |
| LCB710STR | Single-Pole Normally Closed OptoMOS Relay | IXYS |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |