|
|
PDF AH8503 Data sheet ( Hoja de datos )
| Número de pieza | AH8503 | |
| Descripción | HIGH ACCURACY MICROPOWER LINEAR HALL EFFECT SENSOR | |
| Fabricantes | Diodes | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AH8503 (archivo pdf) en la parte inferior de esta página. Total 19 Páginas | ||
|
No Preview Available !
AH8503
HIGH ACCURACY MICROPOWER
LINEAR HALL EFFECT SENSOR
Description
The AH8503 is a high accuracy, micropower linear Hall effect sensor
with an 8-bit output resolution. The output voltage is ratiometric to the
supply voltage and proportional to the magnetic flux density
perpendicular to the part marking surface. The output null voltage is
at half the supply voltage.
Pin Assignments
(Top View)
AH8503 is a trimmed device with typical sensitivity of 2.25mV/G and
3.8mV/G at 1.8V and 3V respectively with an accuracy of 3% at
+25°C. The device has a typical input referred rms noise of 0.36G and
0.24G at 1.8V and 3.0V.
Designed for battery powered consumer equipment to office
equipment, home appliances and industrial applications, the AH8503
can operate over the supply range of 1.6V to 3.6V. The device has a
CNTRL pin to select the operating modes and sampling rate to
minimize power consumption. The device operates in default
micropower mode with a sampling rate of 24Hz typical and consumes
only 13µA typical at 1.8V. In turbo mode with a continuous 6.25kHz
sample rate, the current consumption is 1mA typical. In external-drive
mode, the CNTRL be can be used to change the sampling frequency
up to 7.14KHz with current consumption of 1.16mA typical at 1.8V.
To minimize PCB space the AH8503 are available in small low profile
U-DFN2020-6.
Features
• High Accuracy Linear Hall Effect Sensor with +/-400G Sense
Range and Output Voltage with 8-bit resolution
• Supply Voltage of 1.6V to 3.6V
• High Accuracy: Trimmed Sensitivity of 2.225mV/G and 3.8mV/G
at 1.8V and 3V respectively with accuracy of 3% at +25°C.
• Low Offset Voltage
• Micropower (Default), Turbo and External-Drive Modes
• Ultra Low Average Supply Current
13µA typical in micropower mode (default) period at 1.8V
1.01mA typical in turbo mode at 1.8V
1.16mA typical in external drive mode with 7.14kHz
sampling rate at 1.8V
• Chopper Stabilized Design with Superior Temperature Stability,
Minimal Sensitivity Drift, Enhanced Immunity to Physical Stress
• Output Voltage Maintained at ‘Sleep’ Mode
• -40°C to +85°C Operating Temperature
• High ESD capability of 6kV Human Body Model
• Small Low Profile U-DFN2020-6 Package
• Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2)
• Halogen and Antimony Free. “Green” Device (Note 3)
U-DFN2020-6
Applications
• High Accuracy Level, Proximity, Position and Travel Detection
• Button Press Detection in Digital Still, Video Cameras and
Handheld Gaming Consoles
• Accurate Door, Lids and Tray Position Detection
• Liquid Level Detection
• Joy Stick Control – Gaming and Industrial Applications
• Smart Meters
• Contact-Less Level, Proximity and Position Measurement in
Home Appliances and Industrial Applications
Notes:
1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant.
2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green"
and Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and
<1000ppm antimony compounds.
AH8503
Document number: DS37684 Rev. 1 - 2
1 of 19
www.diodes.com
February 2015
© Diodes Incorporated
1 page  
AH8503
Electrical Characteristics (continued) (@TA = +25°C, VDD = 1.8V, unless otherwise specified.)
CNTRL pin timing, conversion rate and IDD supply current relationship
AH8503 CNTRL Pin Driven Externally – External Drive Mode
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28
ten
EN
TCONV
OUT
Tclk
DATA0
DATA1
Status
AWAKE(ON)
SLEEP
AWAKE(ON)
SLEEP
ICC
1.35mA
8.9µA
1.35mA
8.9µA
Status: AWAKE: chip processing phase (12*Tclk) ,
SLEEP: chip retain data
Tclk: internal clock period, typical = 10µs
ten : pulse width of enable signal, minimum=2*Tclk= 20µs (typical)
TCONV: One sample/conversion cycle = 14*Tclk= 140µs (typical)
IDD ( @ VDD = 1.8V, 25oC):
(1) If CNTRL pin clocked at maximum (~7.14 kHz): IDD = 1.35 mA*12/14+8.93µA*2/14 ≈ 1.16mA
(2) If CNTRL pin clocked at 24Hz: IDD ≈ 13µA
(3) If CNTRL clocking period =T, IDD = 1.35mA*120µs/T + 8.93µA*(T-120µs)/T
AH8503 CNTRL = GND or Logic Low (0) Continuously – Micropower Mode
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 4095 4096 4097 4098 4099 4100 4101 4102 4103 4104 4105 4106 4107 4108 4109 4110
EN TS=4096*Tclk
OUT
DATA0
DATA1
Status
AWAKE(ON)
SLEEP
AWAKE(ON)
SLEEP
ICC 1.35mA
8.9uA
1.35mA
8.9uA
Tclk: internal clock period, typical= 10µs
TS: awake cycle time = 4096*Tclk ≈ 41ms
AH8503 CNTRL = VDD or Logic High Continuously – Turbo Mode
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
EN
OUT Tclk
TCONV
DATA0
Status
AWAKE(ON)
SLEEP
AWAKE(ON)
ICC
1.35mA
8.9µA
Tclk: internal clock period, typical= 10µs
TCONV: One sample/conversion period when ENABLE = Hugh (VDD )= 16*Tclk=160µs
IDD ( @ VDD = 1.8V, 25oC):
IDD = 1.35mA*120µs/160µs + 8.93µA*40µs/160µs ≈ 1.01mA (typical)
1.35mA
DATA1
SLEEP
8.9µA
AH8503
Document number: DS37684 Rev. 1 - 2
5 of 19
www.diodes.com
February 2015
© Diodes Incorporated
5 Page 
AH8503
Typical Operating Characteristics
Average Supply Current
Micropower Mode – 24Hz Sample Rate
24.0
22.0 Micropower Mode, CNTRL = GND, TA = +25 °C,
20.0
18.0
16.0
14.0
12.0
10.0
8.0
6.0
4.0
2.0
0.0
1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 3.8
Supply Voltage (V)
Average Supply Current (CNTRL= GND) vs Supply Voltage
Micropower Mode – 24Hz Sample Rate
24.0
22.0 Micropower Mode, CNTRL = GND
20.0
18.0
16.0
14.0
3.6V
3.3V
3.0V
2.5V
12.0 1.8V
10.0 1.6V
8.0
6.0
4.0
2.0
0.0
-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90
Temperature (oC)
Average Supply Current (CNTRL = GND) vs Temperature
Turbo Mode – 6.25kHz Sample Rate
2.4
2.2 Turbo Mode, CNTRL = VDD , TA = +25 °C
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 3.8
Supply Voltage (V)
Average Supply Current (CNTRL = VDD) vs Supply Voltage
Turbo Mode – 6.25kHz Sample Rate
2.8
2.6
Turbo Mode, CNTRL = VDD
2.4
2.2
3.6V
3.3V
2.0 3.0V
1.8
1.6 2.5V
1.4
1.2
1.0
1.8V
0.8 1.6V
0.6
0.4
0.2
0.0
-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90
Temperature (oC)
Average Supply Current (CNTRL = VDD) vs Temperature
External Drive Mode with 7.14kHz Sampling Rate
2.4
2.2 Externally Driven, CNTRL = 20µs pulse 7.14kHz PWM, TA = +25 °C
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 3.8
Supply Voltage (V)
Average Supply Current (CNTRL = PWM) vs Supply Voltage
External Drive Mode with 7.14kHz Sampling Rate
2.8
2.6
Externally Driven, CNTRL = 20µs pulse 7.14kHz PWM
2.4
2.2 3.6V
2.0
1.8
1.6
3.3V
3.0V
2.5V
1.4 1.8V
1.2 1.6V
1.0
0.8
0.6
0.4
0.2
0.0
-50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90
Temperature (oC)
Average Supply Current (CNTRL = PWM) vs Temperature
AH8503
Document number: DS37684 Rev. 1 - 2
11 of 19
www.diodes.com
February 2015
© Diodes Incorporated
11 Page | ||
| Páginas | Total 19 Páginas | |
| PDF Descargar | [ Datasheet AH8503.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AH8500 | LOW POWER/MICROPOWER LINEAR HALL EFFECT SENSOR | Diodes |
| AH8501 | HIGH ACCURACY LOW POWER / MICROPOWER LINEAR HALL EFFECT SENSOR | Diodes |
| AH8502 | MICROPOWER LINEAR HALL EFFECT SENSOR | Diodes |
| AH8503 | HIGH ACCURACY MICROPOWER LINEAR HALL EFFECT SENSOR | Diodes |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |