DataSheet.es    


PDF 1.5KE11CA Data sheet ( Hoja de datos )

Número de pieza 1.5KE11CA
Descripción TVS Diodes
Fabricantes Littelfuse 
Logotipo Littelfuse Logotipo



Hay una vista previa y un enlace de descarga de 1.5KE11CA (archivo pdf) en la parte inferior de esta página.


Total 6 Páginas

No Preview Available ! 1.5KE11CA Hoja de datos, Descripción, Manual

1.5KE Series
TVS Diodes
Axial Leaded – 1500W > 1.5KE series
RoHS
Pb e3
Uni-directional
Description
The 1.5KE Series is designed specifically to protect
sensitive electronic equipment from voltage transients
induced by lightning and other transient voltage events.
Bi-directional
Agency Approvals
AGENCY
AGENCY FILE NUMBER
E128662/E230531
Maximum Ratings and Thermal Characteristics
(TA=25OC unless otherwise noted)
Parameter
Peak Pulse Power Dissipation by
10/1000μs Test Waveform (Fig.2)
(Note 1)
Steady State Power Dissipation on
Inifinite Heat Sink at TL=75ºC (Fig. 6)
Peak Forward Surge Current, 8.3ms
Single Half Sine Wave Unidirectional
Only (Note 2)
Maximum Instantaneous Forward
Voltage at 100A for Unidirectional
Only (Note 3)
Operating Junction and Storage
Temperature Range
Typical Thermal Resistance Junction
to Lead
Typical Thermal Resistance Junction
to Ambient
Symbol
PPPM
PD
IFSM
VF
TJ, TSTG
RuJL
RuJA
Value
1500
6.5
200
3.5/5.0
-55 to 175
15
75
Unit
W
W
A
V
°C
°C/W
°C/W
Notes:
1. Non-repetitive current pulse , per Fig. 4 and derated above TA = 25OC per Fig. 3.
2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per
minute maximum.
3. VF<3.5V for devices of VBR <_ 200V and VF<5.0V for devices of VBR >_ 201V.
Functional Diagram
Features
VBR @TJ= VBR@25°C x (1+αT
x (TJ - 25))
(αT:Temperature Coefficient)
• Glass passivated chip
junction in DO-201
Package
• 1500W peak pulse
capability at 10/1000μs
waveform, repetition rate
(duty cycles):0.01%
• Fast response time:
typically less than 1.0ps
from 0 Volts to BV min
• Excellent clamping
capability
• T ypical failure mode is
short from over-specified
voltage or current
• W hisker test is conducted
based on JEDEC
JESD201A per its table 4a
and 4c
• IEC-61000-4-2 ESD
15kV(Air), 8kV (Contact)
• ESD protection of data
lines in accordance with
IEC 61000-4-2 (IEC801-2)
• EFT protection of data
lines in accordance with
IEC 61000-4-4 (IEC801-4)
• Low incremental surge
resistance
aTybpoivceal1I3RVless than 1μA
• High temperature
soldering guaranteed:
260°C/40 seconds /
0.375”,(9.5mm) lead
length, 5 lbs., (2.3kg)
tension
• Plastic package has
underwriters laboratory
flammability classification
94V-O
• Matte tin lead–free plated
• Halogen free and RoHS
compliant
• 2nd level interconnect is
Pb-free per IPC/JEDEC
J-STD-609A.01
Applications
TVS devices are ideal for the protection of I/O interfaces,
cVoCCmbpuustearn, dinodtuhsetrriavlualnnedracbolnescuimrcueirtseluescetrdoninictealpepcloicmat,ions.
Cathode
1.5KE Series
Bi-directional
Uni-directional
Anode
118
©2014 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 10/09/14

1 page




1.5KE11CA pdf
TVS Diodes
Axial Leaded – 1500W > 1.5KE series
Soldering Parameters
Reflow Condition
- Temperature Min (Ts(min))
Pre Heat - Temperature Max (Ts(max))
- Time (min to max) (ts)
Average ramp up rate (Liquidus Temp (TL)
to peak
TS(max) to TL - Ramp-up Rate
Reflow
- Temperature (TL) (Liquidus)
- Time (min to max) (ts)
Peak Temperature (TP)
Time within 5°C of actual peak
Temperature (tp)
Ramp-down Rate
Time 25°C to peak Temperature (TP)
Do not exceed
Lead–free assembly
150°C
200°C
60 – 180 secs
3°C/second max
3°C/second max
217°C
60 – 150 seconds
260+0/-5 °C
20 – 40 seconds
6°C/second max
8 minutes Max.
280°C
TP
TL
Ts(max)
Ts(min)
25˚C
Ramp-up
tp
tL
Critical Zone
TL to TP
ts
Preheat
Ramp-down
t 25˚C to Peak
Time (t)
Flow/Wave Soldering (Solder Dipping)
Peak Temperature :
Dipping Time :
Soldering :
265OC
10 seconds
1 time
Physical Specifications
Weight
Case
Polarity
Terminal
0.045oz., 1.2g
JEDEC DO-201 molded plastic body over
passivated junction.
Color band denotes the cathode except
Bipolar.
Matte Tin axial leads, solderable per
JESD22-B102.
Environmental Specifications
High Temp. Storage
HTRB
Temperature Cycling
H3TRB
RSH
JESD22-A103
JESD22-A108
JESD22-A104
JESD22-A101
JESD22-B106
Dimensions
D
A
Cathode Band
(for Uni-directional products only)
C
B
DO-201
A
Dimensions
A
B
C
D
Inches
Min Max
1.000
-
0.285
0.375
0.038
0.042
0.190
0.210
Millimeters
Min Max
25.40
-
7.20 9.50
0.96 1.07
4.80 5.30
1.5KE Series
122 ©2014 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 10/09/14

5 Page










PáginasTotal 6 Páginas
PDF Descargar[ Datasheet 1.5KE11CA.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
1.5KE11CHYB 39S16400CT-8Won-Top Electronics
Won-Top Electronics
1.5KE11C1500 Watt Transient Voltage Suppressors 6.8 to 400 VoltsMicro Commercial Components
Micro Commercial Components
1.5KE11CGLASS PASSIVATED JUNCTION TRANSIENT VOLTAGE SUPPRESSOR VOLTAGE-6.8 to 440 VoltsSurge Components
Surge Components
1.5KE11C1500 WATT AXIAL TRANSIENT VOLTAGE SUPPRESSORSLittelfuse
Littelfuse

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar