|
|
Número de pieza | A8180 | |
Descripción | 1.4A STEP-DOWN LED DRIVER | |
Fabricantes | AiT Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de A8180 (archivo pdf) en la parte inferior de esta página. Total 20 Páginas | ||
No Preview Available ! AiT Semiconductor Inc.
www.ait-ic.com
A8180
36V, 1.4A STEP-DOWN LED DRIVER
HIGH BRIGHTNESS WITH INTERNAL SWITCH
DESCRIPTION
The A8180 is a continuous mode inductive step-down
converter, designed for driving single or multiple series
connected LEDs efficiently from a voltage source higher
than the LED voltage. The device operates from an input
supply between 6V and 36V and provides an externally
output current up to 1.4A. Depending upon supply
voltage and external components, this can provides up
to 24 watts of output power.
The A8180 includes the output switch and a high-side
output current sensing circuit, which uses an external
resistor to set the nominal average output current.
Output current can be adjusted by applying an external
control signal to the 'ADJ' pin. The ADJ pin will accept
either a DC voltage or a PWM waveform. During DC
dimming, this will provide a continuous output current
that is proportional to the external applied DC voltage.
During the PWM dimming, this will provide a gated
output current and the average current is proportional to
the duty cycle. Applying a voltage of 0.2V or lower to the
ADJ pin turns the output off and switches the device into
a low current standby state.
FEATURES
Simple low parts count
Internal 36V NDMOS switch
Up to 1.4A output current
Single pin on/off and brightness control
using DC voltage or PWM
Soft Start
High efficiency (up to 97%)
Wide input voltage range: 6V to 36V
Output shutdown
Up to 1MHz switching frequency
Inherent open-circuit LED protection
Typical 3% output current accuracy
High-side current sense
Hysteretic control: no compensation
Adjustable constant LED current
Over temperature protection
Available in SOT-89-5 and SOP8 packages
APPLICATIONS
Low voltage halogen replacement LEDs
Automotive lighting
Low voltage industrial lighting
LED back-up lighting
Illuminated signs
LCD TV backlighting
The A8180 is available in SOT-89-5 and SOP8
Packages.
TYPICAL APPLICATION
ORDERING INFORMATION
Package Type
Part Number
SOT89-5
SOP8
Note
K5
A8180K5R
A8180K5VR
M8
A8180M8R
A8180M8VR
V: Green Package
R : Tape & Reel
AiT provides all Pb free products
Suffix “ V “ means Green Package
REV1.1
- APR 2010 RELEASED, MAR 2011 REVISED -
-1-
1 page AiT Semiconductor Inc.
www.ait-ic.com
A8180
36V, 1.4A STEP-DOWN LED DRIVER
HIGH BRIGHTNESS WITH INTERNAL SWITCH
TYPICAL PERFORMANCE CHARACTERISTICS
Test conditions: VIN =12V, RS=0.1Ω, TA = 25°C, unless otherwise specified.
1. Efficiency vs. Supply Voltage
2. Output Current Variation vs. Supply Voltage
L=33uH
L=33uH
3. Operating Frequency vs. Input Voltage
L=33uH
4. Duty Cycle vs. Input Voltage
L=33uH
5. Output Current vs. Supply Voltage
L=33uH
6. Output Current Variation vs. Supply Voltage
L=47uH
REV1.1
- APR 2010 RELEASED, MAR 2011 REVISED -
-5-
5 Page AiT Semiconductor Inc.
www.ait-ic.com
A8180
36V, 1.4A STEP-DOWN LED DRIVER
HIGH BRIGHTNESS WITH INTERNAL SWITCH
Setting Nominal Average Output Current with External Resistor RS
The nominal average output current in the LED(s) is determined by the value of the external current sense
resistor (RS) connected between VIN and ISENSE and is given by:
This equation is valid when ADJ pin is float or applied with a voltage higher than 1.2V (must be less than or
equal to 5V). Actually, RS sets the maximum average current which can be adjusted to a less one by dimming.
The table below gives values of nominal average output current for several preferred values of current setting
resistor (RS) in the typical application circuit shown on page 1.
Nominal Average Output Current (mA)
1000
760
667
333
Rs(Ω)
0.1
0.13
0.15
0.3
Output Current Adjustment by External DC Control
The ADJ pin can be driven by an external dc voltage (VADJ), as shown, to adjust the output current to a value
below the nominal average value defined by RS.
REV1.1
- APR 2010 RELEASED, MAR 2011 REVISED -
- 11 -
11 Page |
Páginas | Total 20 Páginas | |
PDF Descargar | [ Datasheet A8180.PDF ] |
Número de pieza | Descripción | Fabricantes |
A8180 | 1.4A STEP-DOWN LED DRIVER | AiT Semiconductor |
A8180SLU | Surface-Mount/ Low Quiescent Current/ Low Dropout Voltage Dropper Type | Sanken electric |
A8181 | HIGH BRIGHTNESS LED DRIVER | AiT Semiconductor |
A8181SLB | Surface-Mount/ Low Circuit Current/ Low Dropout Voltage Dropper Type | Sanken electric |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |