DataSheet.es    


PDF FAR-2807 Data sheet ( Hoja de datos )

Número de pieza FAR-2807
Descripción OPERATOR MANUAL
Fabricantes FURUNO 
Logotipo FURUNO Logotipo



Hay una vista previa y un enlace de descarga de FAR-2807 (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! FAR-2807 Hoja de datos, Descripción, Manual

OPERATOR'S MANUAL
MARINE RADAR
FAR-2807(-D) Series
MODEL FAR-2107(-BB,-D) Series
(Fishing Specification)
www.furuno.co.jp

1 page




FAR-2807 pdf
SAFETY INSTRUCTIONS
WARNING
ELECTRICAL SHOCK HAZARD
Do not open the equipment.
Only qualified personnel
should work inside the
equipment.
Turn off the radar power
switch before servicing the
antenna unit. Post a warn-
ing sign near the switch
indicating it should not be
turned on while the antenna
unit is being serviced.
Prevent the potential risk of
being struck by the rotating
antenna and exposure to
RF radiation hazard.
Wear a safety belt and hard
hat when working on the
antenna unit.
Serious injury or death can
result if someone falls from
the radar antenna mast.
Do not disassemble or modify the
equipment.
Fire, electrical shock or serious injury can
result.
Immediately turn off the power at the
ship's mains switchboard if water
leaks into the equipment or the equip-
ment is emitting smoke or fire.
Continued use can cause fatal damage to
the equipment.
WARNING
Use the proper fuse.
Use of a wrong fuse can result in damage
to the equipment or cause fire.
Keep heater away from equipment.
Heat can alter equipment shape and melt
the power cord, which can cause fire or
electrical shock.
Do not place liquid-filled containers
near the equipment.
Fire or electrical shock can result if a liquid
spills into the equipment.
Do not operate the equipment with wet
hands.
Electrical shock can result.
Before servicing the radar, turn off
the appropriate external breaker.
Power is not removed from the radar simply
by turning off its power switch.
iii

5 Page





FAR-2807 arduino
TABLE OF CONTENTS
4.5.2 Sleeping all targets ........................................................................................... 4-6
4.6 Setting Up for a Voyage .............................................................................................. 4-7
4.7 Target Data .................................................................................................................. 4-9
4.7.1 Basic target data ............................................................................................... 4-9
4.7.2 Detailed target data......................................................................................... 4-10
4.7.3 Removing a target data display ...................................................................... 4-10
4.7.4 Canceling tracking on a target from target data display.................................. 4-10
4.8 AIS Symbol Attributes.................................................................................................4-11
4.8.1 AIS symbol brilliance .......................................................................................4-11
4.8.2 AIS symbol size and color ...............................................................................4-11
4.9 Past Position Display................................................................................................. 4-12
4.9.1 Past position plot interval................................................................................ 4-12
4.9.2 Past position points......................................................................................... 4-13
4.9.3 Past position display motion ........................................................................... 4-13
4.9.4 Stabilization in true motion.............................................................................. 4-13
4.10 Lost Target................................................................................................................. 4-14
4.10.1 Lost target filter ............................................................................................... 4-14
4.10.2 Enabling, disabling the lost target alarm ......................................................... 4-15
4.11 ROT Setting............................................................................................................... 4-16
4.12 AIS Collision Alarm (CPA, TCPA) .............................................................................. 4-17
4.12.1 Setting the CPA and TCPA ranges.................................................................. 4-17
4.12.2 Enabling, disabling the AIS collision alarm ..................................................... 4-17
4.12.3 Limiting the function of the collision alarm ...................................................... 4-18
4.13 Association of TT and AIS Targets............................................................................. 4-19
4.14 Own Ship’s Data........................................................................................................ 4-21
4.15 Messages .................................................................................................................. 4-22
4.15.1 Creating, saving messages ............................................................................ 4-22
4.15.2 Transmitting messages................................................................................... 4-23
4.15.3 Viewing messages .......................................................................................... 4-24
4.16 AIS System Messages .............................................................................................. 4-26
5. VIDEO PLOTTER OPERATION.................................................................... 5-1
5.1 General........................................................................................................................ 5-1
5.2 Display Modes ............................................................................................................. 5-1
5.3 Presentation Modes..................................................................................................... 5-2
5.4 Radar Map................................................................................................................... 5-3
5.4.1 Showing, hiding the radar map display............................................................. 5-3
5.4.2 Inscribing radar map marks and lines ............................................................... 5-4
5.5 Erasing Radar Map Marks and Lines .......................................................................... 5-6
5.5.1 Erasing individual radar map marks and lines .................................................. 5-6
5.5.2 Erasing all radar map marks and lines ............................................................. 5-7
5.6 Radar Map Corrections ............................................................................................... 5-8
5.6.1 Radar map correction ....................................................................................... 5-8
5.6.2 Cursor data correction ...................................................................................... 5-8
5.7 Chart Cards (A, B, C and W types) ............................................................................. 5-9
5.7.1 Displaying a chart ............................................................................................. 5-9
5.7.2 Chart position correction................................................................................. 5-10
5.7.3 Correcting cursor data .................................................................................... 5-10
5.7.4 Chart land color (B, C and W types) ................................................................5-11
5.8 Hiding, Showing Graphics on the Video Plotter Display ......................................... 5-12
5.9 Track.......................................................................................................................... 5-13
5.9.1 Plotting own ship’s track ................................................................................. 5-13
5.9.2 Plotting interval for other ships' tracks (A, B, C and W types) ........................ 5-14
ix

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet FAR-2807.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
FAR-2807OPERATOR MANUALFURUNO
FURUNO

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar