DataSheet.es    


PDF BD6074GUT Data sheet ( Hoja de datos )

Número de pieza BD6074GUT
Descripción White Backlight LED Drivers
Fabricantes ROHM Semiconductor 
Logotipo ROHM Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de BD6074GUT (archivo pdf) en la parte inferior de esta página.


Total 16 Páginas

No Preview Available ! BD6074GUT Hoja de datos, Descripción, Manual

BD6074GUT
LED Drivers for LCD Backlights
White Backlight LED Drivers
for Small to Medium LCD Panels
(Switching Regulator Type)
BD6074GUT
No.11040EAT39
Description
The BD6074GUT is a white LED driver IC with synchronous rectification that can drive up to 4LEDs.
With synchronous rectification (no external shottky diode required) and small package, they can save mount space.
And the brightness of LED can be adjusted by using PWM pulse on EN pin.
Features
1) Synchronous rectification Boost DC/DC converter
2) No external schottky diode required
3) Driving 4 series white LEDs
4) Over voltage protection
5) Protect open and short output
6) Thermal shut down
7) Brightness adjustment by external PWM pulse
8) Small and Thin CSP package in 8pins
Applications
White LED Backlight
Torch light and easy flash for camera of mobile phone
Absolute maximum ratings (Ta=25)
Parameter
Symbol
Maximum applied voltage 1
VMAX1
Maximum applied voltage 2
Power dissipation
VMAX2
Pd
Ratings
7 *1
20 *1
800 *2
Unit Condition
V Vin, EN, VFB, TEST
V SW, Vout
mW
Operating temperature range
Topr
-30~+85
Storage temperature range
Tstg
-55~+150
*1 These value are based on GND and GNDA pins.
*2 50mm×58mm×1.75mm At glass epoxy board mounting. When it’s used by more than Ta=25 , it’s reduced by 6.4mW/.
Operating rangeTa=-30~+85℃)
Parameter
Symbol
Power supply voltage
Vin
Ratings
Min. Typ. Max.
2.7 3.6 5.5
Unit
V
Condition
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
1/15
2011.12 - Rev.A

1 page




BD6074GUT pdf
BD6074GUT
Electrical characteristic curves (Reference data) – Continued
1.VOUT
Δ=1.66V
5.3ms
2.IIN
Vin=3.6V
Ta=25
1.VOUT
2.IIN
Idd=1.5mA
(4ms/div)
1V/div AC
200mA/div DC
Fig.13 LED Open output voltage
1.EN
2.VOUT
3.VFB
Peak=204mA
4.IIN
(3ms/div)
1.EN 2V/div DC 2.VOUT 5V/div DC
3.VFB 500mV/div DC 4.IIN 200mA/div DC
Fig.14 LED brightness adjustment
Technical Note
1.EN
2.VOUT
3. VFB
Peak=368mA
4. IIN
Vin=3.6VV, iTna==32.65Vo,CTa=25
4LED, 344mLEADL,o3a4dmA Load
Fig.15 Soft Start
500
450
400
VIN=3.6V
350
300 VIN=3.1V
250 VIN=5.5V
200
150 VIN=4.2V
100 VIN=2.9V
50
0
0 10 20 30 40 50 60 70 80 90 100
Duty[%]
Fig.16 LED brightness adjustment
for PWM control
50
40 VIN=4.2V
30
VIN=3.9V
20 VIN=3.1V
VIN=5.2V
10
0
0 2 4 6 8 10
Duty[%]
Fig.17 LED brightness adjustment
for PWM control (Expansion)
50%
40%
30%
20%
10%
0%
-10%
-20%
-30%
-40%
-50%
0
VIN=5.2V
VIN=4.2V
VIN=3.6V
VIN=3.1V
24 6
Duty[%]
8
10
Fig.18 LED brightness variation
for PWM control
(comparison of VFB at VIN=3.9V)
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
5/15
2011.12 - Rev.A

5 Page





BD6074GUT arduino
BD6074GUT
Technical Note
Selection of external parts
Recommended external parts are listed as below.
When to use other parts than these, select the following equivalent components.
Coil
Value Tolerance Manufacturer
22µH
±10%
MURATA
Product number
LQH32CN220K53
Vertical
size
2.5
Size
Horizontal
size
3.2
Height
1.55
22µH
±20%
TDK
VLF3012AT220MR33
2.6
2.8
1.2
22µH
±20%
Coil Craft
DO1608
4.45 6.6 2.92
22µH
±20%
TDK
VLF3010AT220MR33
2.6
2.8
1.0
Please refer to the reference data of p.4 for the change in the efficiency when the coil is changed.
DCR
()
0.71
0.66
0.37
1.30
Capacitor
Value
Manufacturer
CIN
1µF
COUT
1µF
MURATA
MURATA
Product number
GRM188B11A105K
GRM188B11E105K
Vertical
size
Size
Horizontal
size
Height
1.6 0.8 0.8
Temperature
range
-25~+85
1.6 0.8 0.8 -25~+85
Resistor
Value Tolerance Manufacturer
RFB
24
±1%
ROHM
Product number
MCR006YZPF24R0
Vertical
size
Size
Horizontal
size
Height
0.6 0.3 0.23
The coil is the component that is most influential to efficiency. Select the coil which direct current resistor (DCR) and
current - inductance characteristic are excellent. The BD6074GUT are designed for the inductance value of 22µH.
Please do not use other inductance value. Select a capacitor of ceramic type with excellent frequency and temperature
characteristics. Further, select Capacitor to be used for CIN/COUT with small direct current resistance, and pay much
attention to the PCB layout shown in the next page.
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
11/15
2011.12 - Rev.A

11 Page







PáginasTotal 16 Páginas
PDF Descargar[ Datasheet BD6074GUT.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
BD6074GUTWhite Backlight LED DriversROHM Semiconductor
ROHM Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar