|
|
PDF ZP200 Data sheet ( Hoja de datos )
| Número de pieza | ZP200 | |
| Descripción | Electromechanical Positioning Systems Manual | |
| Fabricantes | Parker | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ZP200 (archivo pdf) en la parte inferior de esta página. Total 20 Páginas | ||
|
No Preview Available !
Manual No. 100-5324-01
Rev. 3
ZP200 Series
Product Manual
Effective: November 17, 2004
Supersedes: October 17, 2003
Electromechanical
Positioning Systems
1 page  
ZP200 Series Product Manual
Chapter 1 - Introduction
Chapter 1 - Introduction
Product Description
ZP200 Positioner
The ZP200 Z axis lift table is a stable support platform which provides precise vertical translation and
positioning, while maintaining X-Y integrity. Recirculating square rail bearings are incorporated into a
unique variation of “wedge” mechanics to enable reliable high dynamic performance without the potential
loss of travel encountered with crossed roller bearings. The ZP200 is compatible with XR and LXR
tables for multi-axis systems, and it can be utilized as the system base axis or top axis to fit the motion
requirements of the application. Standard mounting holes and dowel pin holes accommodate repeatable
mounting.
Unpacking
Unpacking
Carefully remove the positioner from the shipping crate and inspect the unit for any evidence of shipping
damage. Report any damage immediately to your local authorized distributor. Please save the shipping
crate for damage inspection or future transportation.
Incorrect handling of the positioner may adversely affect the performance of the unit in its application.
Please observe the following guidelines for handling and mounting of your new positioner.
• DO NOT allow the positioner to drop onto the mounting surface. Dropping the positioner can generate impact
loads that may result in flat spots on bearing surfaces or misalignment of drive components.
• DO NOT drill holes into the positioner. Drilling holes into the positioner can generate particles and machining
forces that may effect the operation of the positioner. Parker Hannifin Corporation will drill holes if necessary;
contact your local authorized distributor.
• DO NOT subject the unit to impact loads such as hammering, riveting, etc. Impacts loads generated by
hammering or riveting may result in flat spots on bearing surfaces or misalignment of drive components.
• DO NOT submerge the positioner in liquids.
• DO NOT disassemble positioner. Unauthorized adjustments may alter the positioner’s specifications and void
the product warranty.
5
www.parkermotion.com
Parker Hannifin Corporation
1140 Sandy Hill Road
Irwin, PA 15642
5 Page 
ZP200 Series Product Manual
Chapter 2 – ZP200 Series Table Specifications
ZP200 Series Technical Data
The useful life of a linear table at full catalog specifications is dependent on the forces acting upon it. These forces include both
static components resulting from payload weight, and dynamic components due to acceleration/deceleration of the load. In multi-
axes applications, the primary positioner at the bottom of the stack usually establishes the load limits for the combined axes. When
determining load/life, it is critical to include the weight of all positioning elements that contribute to the load supported by the primary
axis. The life/load charts are used to establish the table life relative to the applied loads.
Table Life/Load Chart
Compression (normal load)
The graphs provide a preliminary evaluation of the support bearing life/load characteristics. The curves show the life/load
relationship when the applied load is centered on the carriage, normal (perpendicular) to the carriage mounting surface.
11
www.parkermotion.com
Parker Hannifin Corporation
1140 Sandy Hill Road
Irwin, PA 15642
11 Page | ||
| Páginas | Total 20 Páginas | |
| PDF Descargar | [ Datasheet ZP200.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ZP200 | Electromechanical Positioning Systems Manual | Parker |
| ZP2000A | silicon rectifier |  HUYU |
| ZP200A | Rectifier Diode |  HUAJING |
| ZP200A | silicon rectifier | HUYU |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |