DataSheet.es    


PDF R5F5631BDDFC Data sheet ( Hoja de datos )

Número de pieza R5F5631BDDFC
Descripción 100-MHz 32-bit RX MCU
Fabricantes Renesas 
Logotipo Renesas Logotipo



Hay una vista previa y un enlace de descarga de R5F5631BDDFC (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! R5F5631BDDFC Hoja de datos, Descripción, Manual

Features
RX63N Group, RX631 Group
Renesas MCUs
R01DS0098EJ0180
100-MHz 32-bit RX MCU, on-chip FPU, 165 DMIPS, up to 2-MB flash
memory, various communications interfaces including Ethernet MAC,
Rev.1.80
May 13, 2014
full-speed USB 2.0 host/function/OTG interface, CAN, 10- & 12-bit A/D
converters, RTC
Features
RX63N Group products incorporate an Ethernet controller while
RX631 Group products do not.
32-bit RX CPU core
Max. operating frequency: 100 MHz
Capable of 165 DMIPS in operation at 100 MHz
Single precision 32-bit IEEE-754 floating point
Two types of multiply-and-accumulation unit (between memories and
between registers)
32-bit multiplier (fastest instruction execution takes one CPU clock cycle)
Divider (fastest instruction execution takes two CPU clock cycles)
Fast interrupt
CISC Harvard architecture with 5-stage pipeline
Variable-length instructions: Ultra-compact code
Supports the memory protection unit (MPU)
JTAG and FINE (two-line) debugging interfaces
Low-power design and architecture
Operation from a single 2.7- to 3.6-V supply
Low power consumption: A product that supports all peripheral functions
draws only 500 μA/MHz.
RTC is capable of operation from a dedicated power supply (min. operating
voltage: 2.3 V).
Four low-power modes
On-chip main flash memory, no wait states
Supports ROM-less versions and versions with up to 2 Mbytes of ROM
(ROMless/256 Kbytes/384 Kbytes/512 Kbytes: RX631 Group only)
100-MHz operation, 10-ns read cycle (no wait states)
768-Kbyte to 2-Mbyte capacities
User code is programmable by on-board or off-board programming
On-chip data flash memory
ROM-less or 32 Kbytes of ROM (reprogrammable up to 100,000 times)
Programming/erasing as background operations (BGOs)
On-chip SRAM, no wait states
64 Kbytes/128 Kbytes/192 Kbytes/256 Kbytes of SRAM
For instructions and operands
Can provide backup on deep software standby
DMA
DMAC: Four channels
DTC
EXDMAC: Two channels
Dedicated DMAC for the Ethernet controller: Single channel
Reset and supply management
Power-on reset (POR)
Low voltage detection (LVD) with voltage settings
Clock functions
External crystal oscillator or internal PLL for operation at 4 to 16 MHz
Internal 125-kHz LOCO and 50-MHz HOCO
125-kHz clocks for the IWDT
Real-time clock
Adjustment functions (30 seconds, leap year, and error)
Time capture function
(for capturing times in response to event-signal input on external pins)
Independent watchdog timer
125-kHz LOCO clock operation
Useful functions for IEC60730 compliance
Oscillation-stoppage detection, frequency measurement, CRC, IWDT, self-
diagnostic function for the A/D converter, etc.
PLQP0176KB-A 24 × 24 mm, 0.5-mm pitch
PLQP0144KA-A 20 × 20 mm, 0.5-mm pitch
PLQP0100KB-A 14 × 14 mm, 0.5-mm pitch
PLQP0064KB-A 10 × 10 mm, 0.5-mm pitch
PLQP0048KB-A 7 × 7 mm, 0.5-mm pitch
PTLG0177KA-A 8 × 8 mm, 0.5-mm pitch
PTLG0145KA-A 7 × 7 mm, 0.5-mm pitch
PTLG0100JA-A 7 × 7 mm, 0.65-mm pitch
PTLG0064JA-A 6 × 6 mm, 0.65-mm pitch
PLBG0176GA-A 13 × 13mm, 0.8-mm pitch
Various communications interfaces
Ethernet MAC (1) (not in RX631 Group products)
Host/function or OTG controller (1) and function controller (1) with full-
speed USB 2.0 transfer
CAN (compliant with ISO11898-1), incorporating 32 mailboxes (up to 3
modules)
SCI with multiple functionalities (up to 13)
Choose from among asynchronous mode, clock-synchronous mode, smart-
card interface mode, simplified SPI, simplified I2C, and extended serial
mode.
I2C bus interface for transfer at up to 1 Mbps (up to 4)
RSPI for high-speed transfer (up to 3)
Parallel data capture unit (PDC) (1) (available for 512 Kbytes/384 Kbytes/
256 Kbytes flash memory with 177-pin, 176-pin, 145-pin, and 144-pin)
External address space
Buses for high-speed data transfer (max. operating frequency of 50 MHz)
8 CS areas (8 × 16 Mbytes)
Multiplexed bus or separate bus are selectable per area.
8-, 16-, or 32-bit bus space is selectable per area
Independent SDRAM area (128 Mbytes)
Up to 20 extended-function timers
16-bit MTU2: input capture, output compare, PWM waveform output,
phase-counting mode (6 channels)
16-bit TPU: input capture, output compare, phase-counting mode (12
channels)
8-bit TMR (4 channels)
16-bit compare-match timers (4 channels)
A/D converter for 1-MHz Operation
Up to 21 × 12-bit channels, and incorporating 1 sample-and-hold circuit
Up to 8 × 10-bit channels, and incorporating 1 sample-and-hold circuit
Addition of results of A/D conversion (in the 12-bit converter)
Self diagnosis (for the 10-bit converter)
10-bit D/A converter: 2 channels
Temperature sensor for measuring temperature within
the chip
DEU
AES encryption and decryption functions
128/192/256-bit key length
ECB/CBC mode
Register write protection can protect values in
important registers against overwriting.
Up to 134 pins for general I/O ports
5-V tolerance, open drain, input pull-up, switchable driving ability
Unique ID
16-byte ID code is provided for each chip (only for the G version)
Operating temp. range
D version: -40 to +85°C
G version: -40 to +105°C
R01DS0098EJ0180 Rev.1.80
May 13, 2014
Page 1 of 208

1 page




R5F5631BDDFC pdf
RX63N Group, RX631 Group
1. Overview
Table 1.1
Outline of Specifications (4/6)
Classification
Timers
Module/Function
Description
16-bit timer pulse unit
(TPUa)
(16 bits x 6 channels) x 2 unit
Maximum of 16 pulse-input/output possible
Select from among seven or eight counter-input clock signals for each channel
Input capture/output compare function
Output of PWM waveforms in up to 15 phases in PWM mode
Buffered operation and phase-counting mode (two phase encoder input) depending on
the channel
Support for cascade-connected operation (32 bits x 2 channels)
PPG output trigger can be generated
Capable of generating conversion start triggers for the A/D converters
Signals from the input capture pins are input via a digital filter
Clock frequency measuring method
Multi-function timer
pulse unit 2 (MTU2a)
(16 bits x 6 channels) x 1 unit
Time bases for the 6 × 16-bit timer channels can be provided via up to sixteen pulse-input/
output lines and three pulse-input lines
Select from among eight counter-input clock signals for each channel (PCLK/1, PCLK/4,
PCLK/16, PCLK/64, MTCLKA, MTCLKB, MTCLKC, MTCLKD) other than channel 5, for
which only four signals are available.
Input capture function
21 output compare/input capture registers
Complementary PWM output mode
Reset synchronous PWM mode
Phase-counting mode
Generation of triggers for A/D converter conversion
Digital filter
Signals from the input capture pins are input via a digital filter
PPG output trigger can be generated
Clock frequency measuring function
Frequency measuring The MTU or unit 0 TPU module can be used to monitor the main clock, subclock,
method (MCK)
HOCO clock, LOCO clock, and PLL clock for abnormal frequencies.
Port output enable 2 Controls the high-impedance state of the MTU’s waveform output pins
(POE2a)
Programmable pulse
generator (PPG)
(4 bits x 4 groups) x 2 units
Pulse output with the MTU2 or TPU output as a trigger
Maximum of 32 pulse-output possible
8-bit timers (TMR)
(8 bits x 2 channels) x 2 units
Select from among seven internal clock signals (PCLK/1, PCLK/2, PCLK/8, PCLK/32,
PCLK/64, PCLK/1024, PCLK/8192) and one external clock signal
Capable of output of pulse trains with desired duty cycles or of PWM signals
The 2 channels of each unit can be cascaded to create a 16-bit timer
Generation of triggers for A/D converter conversion
Capable of generating baud-rate clocks for SCI5, SCI6, and SCI12
Compare match timer (16 bits x 2 channels) x 2 units
(CMT)
Select from among four internal clock signals (PCLK/8, PCLK/32, PCLK/128, PCLK/512)
Realtime clock
(RTCa)
Clock sources: Main clock, subclock
Clock and calendar functions
Interrupt sources: Alarm interrupt, periodic interrupt, and carry interrupt
Battery backup operation
Time-capture facility for three values
Watchdog timer
(WDTA)
14 bits x 1 channel
Select from among 6 counter-input clock signals (PCLK/4, PCLK/64, PCLK/128, PCLK/
512, PCLK/2048, PCLK/8192)
Independent
watchdog timer
(IWDTa)
14 bits x 1 channel
Counter-input clock: IWDT-dedicated on-chip oscillator
Dedicated clock/1, dedicated clock/16, dedicated clock/32, dedicated clock/64, dedicated
clock/128, dedicated clock/256
R01DS0098EJ0180 Rev.1.80
May 13, 2014
Page 5 of 208

5 Page





R5F5631BDDFC arduino
RX63N Group, RX631 Group
1. Overview
Table 1.3
List of Products (3/8)
Group
Part No.
Package
RX63N
R5F563NYHDFP PLQP0100KB-A
(D version) R5F563NYDDFP PLQP0100KB-A
R5F563NWHDFP PLQP0100KB-A
R5F563NWDDFP PLQP0100KB-A
R5F563NWGDFP PLQP0100KB-A*1
R5F563NWCDFP PLQP0100KB-A*1
R5F563NBCDFP PLQP0100KB-A
R5F563NBDDFP PLQP0100KB-A
R5F563NACDFP PLQP0100KB-A
R5F563NADDFP PLQP0100KB-A
RX63N
(G version)
*2
R5F563NFHGFC
R5F563NFDGFC
R5F563NKDGFC
PLQP0176KB-A
PLQP0176KB-A
PLQP0176KB-A
R5F563NEDGFC PLQP0176KB-A
R5F563NDDGFC PLQP0176KB-A
R5F563NYHGFC PLQP0176KB-A
R5F563NYDGFC PLQP0176KB-A
R5F563NWHGFC PLQP0176KB-A
R5F563NWDGFC PLQP0176KB-A
R5F563NBDGFC PLQP0176KB-A
R5F563NADGFC PLQP0176KB-A
R5F563NFHGFB PLQP0144KA-A
R5F563NFDGFB PLQP0144KA-A
R5F563NKDGFB PLQP0144KA-A
R5F563NEDGFB PLQP0144KA-A
R5F563NDDGFB PLQP0144KA-A
R5F563NYHGFB PLQP0144KA-A
R5F563NYDGFB PLQP0144KA-A
R5F563NWHGFB PLQP0144KA-A
R5F563NWDGFB PLQP0144KA-A
R5F563NBDGFB PLQP0144KA-A
R5F563NADGFB PLQP0144KA-A
R5F563NFHGFP PLQP0100KB-A
R5F563NFDGFP PLQP0100KB-A
R5F563NKDGFP PLQP0100KB-A
R5F563NEDGFP PLQP0100KB-A
R5F563NDDGFP PLQP0100KB-A
R5F563NYHGFP PLQP0100KB-A
R5F563NYDGFP PLQP0100KB-A
R5F563NWHGFP PLQP0100KB-A
R5F563NWDGFP PLQP0100KB-A
R5F563NBDGFP PLQP0100KB-A
R5F563NADGFP PLQP0100KB-A
RX631
R5F5631ECDLC
(D version) R5F5631EDDLC
PTLG0177KA-A
PTLG0177KA-A
ROM
Capacity
RAM
Capacity
1 Mbyte
256 Kbytes
1 Mbyte
256 Kbytes
1 Mbyte
192 Kbytes
1 Mbyte
192 Kbytes
1 Mbyte
192 Kbytes
1 Mbyte
192 Kbytes
1 Mbyte
128 Kbytes
1 Mbyte
128 Kbytes
768 Kbytes 128 Kbytes
768 Kbytes 128 Kbytes
2 Mbytes 256 Kbytes
2 Mbytes 256 Kbytes
2 Mbytes 192 Kbytes
2 Mbytes 128 Kbytes
1.5 Mbytes 128 Kbytes
1 Mbyte
256 Kbytes
1 Mbyte
256 Kbytes
1 Mbyte
192 Kbytes
1 Mbyte
192 Kbytes
1 Mbyte
128 Kbytes
768 Kbytes 128 Kbytes
2 Mbytes 256 Kbytes
2 Mbytes 256 Kbytes
2 Mbytes 192 Kbytes
2 Mbytes 128 Kbytes
1.5 Mbytes 128 Kbytes
1 Mbyte
256 Kbytes
1 Mbyte
256 Kbytes
1 Mbyte
192 Kbytes
1 Mbyte
192 Kbytes
1 Mbyte
128 Kbytes
768 Kbytes 128 Kbytes
2 Mbytes 256 Kbytes
2 Mbytes 256 Kbytes
2 Mbytes 192 Kbytes
2 Mbytes 128 Kbytes
1.5 Mbytes 128 Kbytes
1 Mbyte
256 Kbytes
1 Mbyte
256 Kbytes
1 Mbyte
192 Kbytes
1 Mbyte
192 Kbytes
1 Mbyte
128 Kbytes
768 Kbytes 128 Kbytes
2 Mbytes 128 Kbytes
2 Mbytes 128 Kbytes
E2 Data
Flash
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
32 Kbytes
Operating
Operating
Frequency (Max.) Temp. Range
100 MHz
-40 to +85°C
100 MHz
-40 to +85°C
100 MHz
-40 to +85°C
100 MHz
-40 to +85°C
100 MHz
-40 to +85°C
100 MHz
-40 to +85°C
100 MHz
-40 to +85°C
100 MHz
-40 to +85°C
100 MHz
-40 to +85°C
100 MHz
-40 to +85°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +105°C
100 MHz
-40 to +85°C
100 MHz
-40 to +85°C
R01DS0098EJ0180 Rev.1.80
May 13, 2014
Page 11 of 208

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet R5F5631BDDFC.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
R5F5631BDDFB100-MHz 32-bit RX MCURenesas
Renesas
R5F5631BDDFC100-MHz 32-bit RX MCURenesas
Renesas
R5F5631BDDFP100-MHz 32-bit RX MCURenesas
Renesas

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar