|
|
PDF FXA1012WC Data sheet ( Hoja de datos )
| Número de pieza | FXA1012WC | |
| Descripción | Frame Transfer CCD Image Sensor | |
| Fabricantes | NXP Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de FXA1012WC (archivo pdf) en la parte inferior de esta página. Total 17 Páginas | ||
|
No Preview Available !
IMAGE SENSORS
FXA 1012
Frame Transfer CCD Image Sensor
Objective specification
File under Image Sensors
2000 January 7
Philips
Semiconductors
1 page  
Philips Semiconductors
Frame Transfer CCD Image Sensor
Specifications
Absolute Maximum Ratings
GENERAL:
storage temperature
ambient temperature during operation
voltage between any two gates
DC current through any clock phase (absolute value)
OUT current (no short circuit protections)
VOLTAGES IN RELATION TO VPS:
VNS, RD
all other pins
VOLTAGES IN RELATION TO VNS:
RD
VPS
all other pins
Min.
-40
-20
-20
-0.2
0
-0.5
-10
-10
-30
-30
Objective specification
FXA 1012
Max.
+80
+60
+20
+2.0
4
+30
+25
+0.5
+0.5
+0.5
Unit
°C
°C
V
µA
mA
V
V
V
V
V
VNS1
VPS
SFD
SFS
OG
RD
DC Conditions
N substrate
P substrate
Source Follower Drain
Source Follower Source
Output Gate
Reset Drain
Number of adjustments
Min. [V]
20
6
19
0
3.5
19
Min.
0
Typical [V]
24
7
20
0
4
20
Max. [V]
28
9
21
0
4.5
21
Typical
0
Max.
1
Max. current
[mA]
22
2
5.5 3
1
-
-
Pin
VNS
1 To set the VNS voltage for optimal Anti-Blooming (vertical overflow drain), it should be adjustable between minimum and maximum values.
2 Currents INS and IPS are specified at overexposure of 100 x Qmax.
3 Measured with Rload = 3.3 kOhms.
AC Clock Level Conditions
IMAGE CLOCKS:
A-clock amplitude
A-clock low level
STORAGE CLOCKS:
B-clock amplitude
B-clock low level
HORIZONTAL AND RESET CLOCKS:
C-clock amplitude
C-clock low level C1, C3
C-clock low level C2, C4
Reset Gate (RG) amplitude
Reset Gate (RG) high level
VNS PULSE:
Charge Reset (CR) pulse on VNS
Min.
11
11
4.5
2.5
4.5
21
4.5
Typical
12
0
12
0
5
0
3
5
22
5
Max.
13
13
5.5
3.5
5.25
23
5.5
Unit
V
V
V
V
V
V
V
V
V
V
2000 January
5
5 Page 
Philips Semiconductors
Frame Transfer CCD Image Sensor
Objective specification
FXA 1012
*Arbitrary units
RGB response
100
90 Red
Green
80
70 Blue
60
50
40
30
20
10
0
400 450 500 550 600 650 700
Wavelenght (nm)
Figure 8 - RGB response
Output Buffer
Conversion factor at output node
Supply current
Bandwidth
RMS readout noise @ 5MHz bandwidth after CDS
Min
Typical
Max
18 20 25
4
95
12 15
Unit
µV/el.
mA
MHz
el.
Dark Condition at 60°C 1
Min.
Average no. of dark signal electrons per pixel after 1/30 sec integration
Dark signal shading
Dark current level @ 60° C
Fixed Pattern Noise 2 (FPN) @ 60° C
1 Typical operating conditions (Image capture mode; 60°C; 1/30s exp. time).
2 FPN is the one-σ value of the highpass image.
Typical
25
1
0.3
15
Max.
0.6
25
Unit
electrons
mV
nA/cm2
electrons
2000 January
11
11 Page | ||
| Páginas | Total 17 Páginas | |
| PDF Descargar | [ Datasheet FXA1012WC.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| FXA1012WC | Frame Transfer CCD Image Sensor | NXP Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |