|
|
PDF K7VT2 Data sheet ( Hoja de datos )
| Número de pieza | K7VT2 | |
| Descripción | Motherboard User Manual | |
| Fabricantes | ASRock | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de K7VT2 (archivo pdf) en la parte inferior de esta página. Total 24 Páginas | ||
|
No Preview Available !
K7VT2
User Manual
Version 1.1
Published November 2002
Copyright©2002 ASRock INC. All rights reserved.
1
1 page  
Voltage monitoring: +12V, +5V, +3V, Vcore;
CPU fan tachometer;
Chassis fan tachometer
PCI slots:
5 slots with PCI Specification 2.2
AGP slot:
1 universal AGP slot,
supports 3.3v / 1.5v, 4X / 2X / 1X AGP cards
AMR slot (optional): 1 slot, supports ASRock MR card, shares the bracket with
the slot PCI 5
USB 2.0:
4 default USB ports and 1 extra set of header for two
additional USB ports upgrade
ASRock I/OTM:
PS/2: 1 keyboard port / 1 mouse port;
1 RJ 45 port;
4 rear default USB ports (USB 2.0);
1 serial port: COM 1;
1 parallel port: ECP/EPP support;
Audio Jack: Line Out/ Line In/ Microphone + Game port
BIOS:
AMI legal BIOS;
Supports “Plug and Play”;
ACPI 1.1 compliance wake up events;
Supports jumperfree;
SMBIOS 2.3.1 support;
CPU frequency stepless control
(only for advanced users’ reference)
OS: Microsoft® Windows® 98 SE / ME / 2000 / XP compliant
1. While CPU overheat is detected, the system will automati-
cally shutdown and the power button on the chassis will be
disabled. Please check if the CPU fan on the motherboard
functions properly before you resume the system.
2. Although K7VT2 offers stepless control, it is not recom-
mended to perform over clocking. Frequencies other than
the recommended CPU bus frequencies may cause the
instability of the system or damage the CPU.
5
5 Page 
2.7 Jumpers Setup
The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “SHORT”. If no jumper
cap is placed on the pins, the jumper is
“OPEN”. The illustration shows a 3-pin
jumper whose pin1 and pin2 are “SHORT”.
Jumper
Setting
Description
FSB_SEL1
(see p.6 item 23)
FSB_SEL1
2_3
FSB_SEL1
1_2
FSB 100 MHz
FSB 133 MHz
Note: Follow the figures to set the CPU front side bus frequency.
PS2_USB_PWR1
1_2
2_3 Short pin2, pin3 to enable
(see p.6 item 26)
+5VSB (standby) for PS/2 or
+5V +5VSB
USB wake up events.
Note: To select +5VSB, it requires 2 Amp and higher standby current.
CLRCMOS1
(see p.6 item 17)
solder points
2.8 Connectors
Disconnect the power cord,
then short the solder points
to clear CMOS by using
metal material, e.g., a paper
clip.
Connectors are NOT jumpers. DO NOT place jumper caps over
these connectors.
Connector
Figure
Description
FDD connector
(33-pin FLOPPY1)
(see p.6 item 10)
Pin1 FLOPPY1
Red marking
Note: Match the red marking on the floppy ribbon cable with Pin1.
Primary IDE connector (Blue) Secondary IDE connector (Black)
(39-pin IDE1, see p.6 item 7) (39-pin IDE2, see p.6 item 8)
PIN1 IDE1
PIN1 IDE2
11
11 Page | ||
| Páginas | Total 24 Páginas | |
| PDF Descargar | [ Datasheet K7VT2.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| K7VT2 | Motherboard User Manual | ASRock |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |