DataSheet.es    


PDF 25L4006E Data sheet ( Hoja de datos )

Número de pieza 25L4006E
Descripción MX25L4006E
Fabricantes MXIC 
Logotipo MXIC Logotipo



Hay una vista previa y un enlace de descarga de 25L4006E (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! 25L4006E Hoja de datos, Descripción, Manual

MX25L4006E
MX25L4006E
DATASHEET
P/N: PM1576
REV. 1.3, FEB. 10, 2012
1
Free Datasheet http://www.datasheet4u.com/

1 page




25L4006E pdf
MX25L4006E
GENERAL DESCRIPTION
The device features a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus.
The four bus signals are a clock input (SCLK), a serial data input (SI), a serial data output (SO), and a chip select (CS#).
Serial access to the device is enabled by CS# input.
When it is in Dual Output read mode, the SI and SO pins become SIO0 and SIO1 pins for data output.
The device provides sequential read operation on whole chip.
After program/erase command is issued, auto program/erase algorithms which program/erase and verify the speci-
fied page or sector/block locations will be executed. Program command is executed on byte basis, or page basis, or
word basis for erase command is executes on sector, or block, or whole chip basis.
To provide user with ease of interface, a status register is included to indicate the status of the chip. The status read
command can be issued to detect completion status of a program or erase operation via WIP bit.
When the device is not in operation and CS# is high, it is put in standby mode.
The device utilizes Macronix's proprietary memory cell, which reliably stores memory contents even after 100,000
program and erase cycles.
PIN CONFIGURATIONS
PIN DESCRIPTION
8-PIN SOP (150/200mil) 8-PIN PDIP (300mil)
CS#
SO/SIO1
WP#
GND
1
2
3
4
CS# 1
8 VCC
7 HOLD# SO/SIO1 2
6 SCLK
WP# 3
5 SI/SIO0
GND 4
8 VCC
7 HOLD#
6 SCLK
5 SI/SIO0
8-LAND, WSON (6x5mm) 8-LAND USON (2x3mm)
CS#
SO/SIO1
WP#
GND
1
2
3
4
8 VCC
7 HOLD#
6 SCLK
5 SI/SIO0
CS#
SO/SIO1
WP#
GND
1
2
3
4
8 VCC
7 HOLD#
6 SCLK
5 SI/SIO0
SYMBOL DESCRIPTION
CS# Chip Select
SI/SIO0
Serial Data Input (for 1 x I/O) / Serial Data
Input & Output (for Dual Output mode)
SO/SIO1
Serial Data Output (for 1 x I/O) / Serial
Data Output (for Dual Output mode)
SCLK Clock Input
WP# Write Protection
HOLD#
Hold, to pause the device without
deselecting the device
VCC + 3.3V Power Supply
GND Ground
P/N: PM1576
REV. 1.3, FEB. 10, 2012
5
Free Datasheet http://www.datasheet4u.com/

5 Page





25L4006E arduino
MX25L4006E
Table 3. COMMAND DEFINITION
COMMAND
(byte)
WREN
(write
Enable)
WRDI
(write disable)
WRSR
(write status
register)
RDID
RDSR
(read
(read status
identification) register)
READ
(read data)
Fast Read
(fast read
data)
1st
2nd
3rd
4th
5th
Action
06 Hex
sets the
(WEL) write
enable latch
bit
04 Hex
01 Hex
9F Hex
reset the to write new output the
(WEL) write status register manufacturer
enable latch
ID and 2-byte
bit device ID
05 Hex
to read out
the status
register
03 Hex
0B Hex
AD1 AD1
AD2 AD2
AD3 AD3
Dummy
n bytes read n bytes read
out until CS# out until CS#
goes high goes high
REMS (Read DREAD
COMMAND RDSFDP RES (Read Electronic (Double
(byte) (Read SFDP) Electronic ID) Manufacturer Output Mode
& Device ID) command)
1st
5A Hex
AB Hex
90 Hex
3B Hex
2nd AD1
x
x AD1
3rd AD2
x
x AD2
4th AD3
x
ADD(1)
AD3
5th Dummy
Dummy
Read SFDP to read out Output the n bytes read
mode 1-byte Device manufacturer out by Dual
Action
ID ID and device Output until
ID CS# goes
high
SE
(Sector
Erase)
20 Hex
AD1
AD2
AD3
to erase the
selected
sector
BE CE
(Block Erase) (Chip Erase)
52 or D8 Hex 60 or C7 Hex
AD1
AD2
AD3
to erase the
selected
block
to erase
whole chip
COMMAND
(byte)
1st
2nd
3rd
4th
5th
Action
PP
(Page
Program)
02 Hex
AD1
AD2
AD3
to program
the selected
page
DP RDP (Release
(Deep Power from Deep
Down) Power-down)
B9 Hex
AB Hex
enters deep release from
power down deep power
mode
down mode
(1) ADD=00H will output the manufacturer's ID first and ADD=01H will output device ID first.
(2) It is not recommended to adopt any other code which is not in the above command definition table.
P/N: PM1576
11
REV. 1.3, FEB. 10, 2012
Free Datasheet http://www.datasheet4u.com/

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet 25L4006E.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
25L4006EMX25L4006EMXIC
MXIC

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar