PDF 2.2K3A2IB Datasheet ( Hoja de datos )

Número de pieza 2.2K3A2IB
Descripción Chip Thermistors
Fabricantes BetaTHERM 
Logotipo BetaTHERM Logotipo

Total 2 Páginas
2.2K3A2IB Hoja de datos, Descripción, Manual
BetaTHERM Sensors
BetaCurve Interchangeable Thermistor Series II
BetaCurve Interchangeable Thermistor Series II
Thermistor Configuration
30 AWG Sliver Plated
Copper Lead Wires
With Etched
TFE Telfon Insulation,
Thermally Conductive
Epoxy Coating
12.7mm +/-3.3mm
(0.50Ó +/-0.13Ó)
76.2mm +/-3.3mm
(3.00Ó +/-3.13Ó)
Max. Dia.
Example: BetaCURVE Series II Part Number
10K 3 A 1 I A
Tolerance Classification
Insulated Lead Wires
BetaCURVE Series
Epoxy Coated
Material Curve #
Resistance Value
¥ Temperature sensing, control and compensation.
¥ P.C. board mounting for over temperature
¥ Automotive car seat heater control and engine
¥ Assembly into probes for a wide variety of
applications in industrial temperature control and
¥ Rapid Time Response (1 second typical in liquids).
¥ DC (Dissipation Constant) = 0.85mW/ oC
typical in still air at 25oC.
¥ Min./Max. Temperature Exposure = -80 to 150oC.
¥ Available in custom probe assemblies.
¥ Proven Stability and Reliability.
¥ Teflon Insulated lead wires.
¥ Choice of 4 temperature tolerance classifications:
Tolerance Code:
+/-0.1oC, 0oC to 70oC
+/-0.2oC, 0oC to 70oC
+/-0.5oC, 0oC to 70oC
+/-1.0oC, 0oC to 70oC
Similar to the BetaCURVE Thermistor Series I, the
Series II thermistors are small epoxy coated devices. The
same quality thermistor elements are used during assembly.
Series II are manufactured using 30 AWG teflon insulated
lead wires. They offer the same choice of precision
temperature tolerance classifications for a wide variety of
customer applications.
The Series II differs from Series I marginally with
respect to D.C. The typical value of 0.85mW/oC in still air
at 25oC is due to the larger lead wire diameter made of pure
The insulated lead wires offer customers the added
protection of TFE teflon insulation that has the highest
temperature rating (150oC) of the most common insulating
materials. TFE teflon is a material that does not bond easily
with epoxies or adhesives. For this reason the surface of the
teflon wire is etched, which enhances bondability for
applications that require mounting or potting the thermistor
with epoxies or adhesives.
The series is produced in high volume as a
Standard configuration. Other configurations are available
on a custom basis. Larger or smaller lead wires can be used
with the same chip elements and with insulating materials of
PVC, Kynar, Tefzel, Nylon/Polyurethane, etc. Contact
Applications Engineering Group for support if requirements
differ from the standard configuration as shown above.
BETA ApS (DK + NO): Phone: +45 59 31 11 88, Fax: +45 59 31 12 10, email:
4 BEATA Komponent AB (SE): Phone: +46 (0)392 360 40, Fax: +46 (0)392 360 41, e-mail:
BETA Finland OY (FI): Phone: +358 (0)9 260 9209, Fax: +358 (0)9 260 9208, e-mai:

1 page

PáginasTotal 2 Páginas
PDF Descargar[ 2.2K3A2IB.PDF ]

Enlace url

Hoja de datos destacado

Número de piezaDescripciónFabricantes
2.2K3A2IBChip ThermistorsBetaTHERM

Número de piezaDescripciónFabricantes

High Voltage 3 phase Motor Driver IC.


12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.    |   2019   |  Privacy Policy  |  Contacto  |  Buscar