|
|
PDF GL5ZJ43 Data sheet ( Hoja de datos )
| Número de pieza | GL5ZJ43 | |
| Descripción | DEVICE SPECIFICATION FOR Light Emitting Diode | |
| Fabricantes | Sharp Electrionic Components | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de GL5ZJ43 (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
|
No Preview Available !
PREPARED BY:
DATE:
suln/tO/?q
r- uQ.ds.
APPROVED BY:
DATE:
lik e5<J-un
.T qKJ7~s-e
ELECTROMC COMPONENTS GROUP
SHARP CORPORATION
SPECIFICATION
SPECNo.
ISSUE
PAGE
REPRESENTATIVE
DG996036
J&16/99
10 pages
DIVISION:
Opto-Electronic Devices Division
DEVICE SPECIFICATION FOR
Light Emitting Diode
MODEL No.
1. These specification sheets include materials protected under the copyright of Sharp Corporation (“Sharp”).
Please do not reproduce or cause anyone to reproduce them without Sharps consent.
2. When using this product, please observe the absolute maximum ratings and the instructions for use outlined
in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility
for any damage resulting from use of the product which does not comply with the absolute maximum ratings
and the instructions included in these specification sheets, and the precautions mentioned below.
(Precautions)
(1) This products is designed for use in the following application areas;
* OA equipment * Audio visual equipment * Home appliance
* Telecommunication equipment (Terminal) * Measuring equipment
L * Tooling machines * Computers
I
If the use of the product in the above application areas is for equipment listed in paragraphs
(2) or (3). please be sure to observe the precautions given in those respective paragraphs.
(2) Appropriate measures, such as fail-safe design and redundant design considering
the safety design of the overall system and equipment, should be taken to ensure reliability
. and safety when this product is used for equipment which demands high reliability and
safety in function and precision, such as ;
* Transportanon control and safety equipment (aircraft, train, automobile etc.)
* Traffic signals * Gas leakage sensor breakers * Rescue and security equipment
[ * Other safety equipment
I
(3) Please do not use this product for equipment which require extremely high reliability
and safety in function and precision, such as ;
* Space equipment * Telecommunication equipment (for trunk lines)
I * Nuclear power control equipment * Medical equipment
1
(4) Please contact and consult with a Sharp sales representative if there are any questions
regarding interpretation of the above three paragraphs.
3. Please contact and consult with a Sharp sales representative for any questions about this product.
CUSTOMERS APPROVAL
DATE:
BY:
DATE:
PRESENTED BY:
M.Katoh,
I
Department General LManager of
Engineering Dept.,III
Opto-Electronic Devices Division
Electronic Components Group
SHARP CORPOluTION
1 page  
Peak Forward Current vs. Duty Ratio
DG996036
MODEL No.
I GL5ZJ43
Jud16/9!3
PAGE
I 4/10
10
l/100
l/10
Duty Raito
1
DR
10
3-4. Characteristics Diagram&p) (Note 1)
Forward Current vs.Forward
loo
Voltage
(Ta=25"C)
0. 1
1 1.2 1.4 1.6 1.8
2 2.2 2.4 2.6
Forward Voltage VFOJ)
Relative
Luminous Intensity
1000
.5- 100
t
G
10
vs. Frorard
Voltap~
(Ta+X'C)
Relative
Luminous Intensity
vs. Ambient Temperature
( I F=2OmN
1000
Iiii”“iiiiItlIltrIllI I I I I I I
: l-00
O-
EE
AJ
.-:
c5,
2 10
-60 -40 -20 0 20 40 60 80 100 120
Ambient Temprature
TarC)_
.z>- ” 0. 1
G
p:
0. 01
0. 1 1
10 100
Forward Current
IFhA)
(Note 1) Above characteristic data are typical data and not a guarantteed data.
5 Page 
DG996036
MODEL No.
GL5ZJ43
JunllWW
PAGE
lo/lo
7 - 3. Soldering Conditions
’ Solder the lead pins under the following conditions
Type of S oldering
Conditions
1. Manual soldering
2. Wave soldering
29%+5”c. within 3 seconds
26O”ck5”c, within 5 seconds
3. Auto soldering
Preheating 70°C to 8O”c, within 30 seconds
Soldering 245”c+5”c, within 5 seconds
(Note) Avoid dipping resin into soldering bath
Avoid applying stress to lead pins while they are heated. For example ,
when the LED lamp is moved with the heat applied to the lead pins during
manual soldering or solder repair,disconnection may occur.
7 - 4. For cleaning
( 1) Solvent cleaning : Solvent temperature 45°C or less
Immersion for 3 min or less
(2 > Ultrasonic
cleaning : The effect to device by ultrasonic cleaning differs
by cleaning bath size,ultrasonic power
output,cleaning time,PW size or device mounting
condition etc. Please test it in actual using condition
and confirm that doesn’t occur any defect before starting
the ultrasonic cleaning.
( 3 > Applicable solvent : Ethyl alcohol, Yethyl alcohol, Isopropyl alcohol
In case when the other solvent is used,there are cases that
the packaging resin is eroded. Please use the other solvent
after thorough confirmation is performed in actual using condition.
11 Page | ||
| Páginas | Total 11 Páginas | |
| PDF Descargar | [ Datasheet GL5ZJ43.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| GL5ZJ43 | DEVICE SPECIFICATION FOR Light Emitting Diode | Sharp Electrionic Components |
| GL5ZJ44 | DEVICE SPECIFICATION FOR Light Emitting Diode | Sharp Electrionic Components |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |