|
|
Número de pieza | LK520D3LZ17 | |
Descripción | TFT LCD Module | |
Fabricantes | Sharp | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de LK520D3LZ17 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! 1 page 45 GND
46 GND
47
VCC
+12V Power Supply
48
VCC
+12V Power Supply
49
VCC
+12V Power Supply
50
VCC
+12V Power Supply
51
VCC
+12V Power Supply
[note]GND of a liquid crystal panel drive part has connected with a module chassis.
LD- 19X10-3
[Note 1] Display reversal function
Normal (Default)
R/L : L (GND) U/D: L (GND)
CN1
Horizontal reverse image
R/L : H (3.3V) U/D: L (GND)
CN1
Vertical reverse image
R/L : L (GND) U/D: H (3.3V)
CN1
Horizontal and vertical reverse image
R/L : H(3.3V) U/D: H (3.3V)
CN1
[Note 2]The equivalent circuit figure of the terminal
100Ω
Terminal
Min : 16.5KΩ
Typ : 47KΩ
Max : 330KΩ
[Note 3]The equivalent circuit figure of the terminal
3.3V
Terminal
4.7KΩ
100Ω
Min : 16.5KΩ
Typ : 60KΩ
Max : 330KΩ
5 Page [Note 2] Brightness Control selection
Pin No.14 is used for the selection of dimming control for VBRT pin (Pin No.13).
Input voltage
0V
3.3V
VBRT
Pulse dimming
Analog dimming
LD- 19X10-9
[Note 3]Brightness Control
1. Analog Dimming
Brightness control is regulated by analog input voltage (0V to 3.3V).
Input voltage [VBRT]
[Reference]
Brightness ratio %
MIN
0V
20
TYP
<->
<->
MAX
3.3V
100
Ta=25
Function
0V: Dark - 3.3V: Bright
[Note] PWM frequency : 275±10Hz
[Note]There is a case that lamp mura may happen, depending on ambient temperature and dimming.
Dimming level should be set according to your evaluation of actual display performance.
(Minimum input voltage 1.4V at below 15 )
2.Pulse Dimming
Pin No.13 is used for the control of the PWM duty with input pulse from 150Hz to 350Hz.
Duty TON/T
Pulse signal
DUTY(TON/T)
Dimming level
(luminance ratio)
[Hz]
[%]
[%]
MIN
150
40
20
TYP
275
<->
<->
MAX
350
100
100
[Reference]The characteristic of the pulse PWM duty vs dimming level
DUTY(TON/T)
40%
60%
80%
100%
Dimming level
(luminance ratio)
20%
45%
70%
100%
Input Condition
Pulse Signal=275Hz
Ta=25
Remark
Ta=25
Ta=25
[Note]There is a case that lamp mura may happen, depending on ambient temperature,
in dimming. Minimum dimming level should be set according to your evaluation of
actual display performance. (Minimum duty 60% at below 15 )
[Note]In case of using Pulse Dimming, be careful so that the VBRT signal (Pin 13) doesn’t have glitch.
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet LK520D3LZ17.PDF ] |
Número de pieza | Descripción | Fabricantes |
LK520D3LZ17 | TFT LCD Module | Sharp |
LK520D3LZ18 | TFt LCD Module | Sharp |
LK520D3LZ19 | TFT-LCD Module | Sharp |
LK520D3LZ1x | TFT LCD Module | Sharp |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |