|
|
PDF V315HH6-LS1 Data sheet ( Hoja de datos )
| Número de pieza | V315HH6-LS1 | |
| Descripción | TFT LCD Module | |
| Fabricantes | CMI MEI | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de V315HH6-LS1 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
ϭʳ Tentative Specification
Ϯʳ Preliminary Specification
ϭʳ Approval Specification
MODEL NO.: V315HH6
SUFFIX: LS1
Customer:
APPROVED BY
Name / Title
Note
SIGNATURE
Please return 1 copy for your confirmation with your
signature and comments.
Approved By
Chao-Chun Chung
Checked By Prepared By
Vincent Chou Samuel Huang
Version 1.3
1 DateΚ11 Feb., 2011
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
1 page  
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
1. GENERAL DESCRIPTION
1.1 OVERVIEW
V315HH6-LS1 is a 31.5” TFT Liquid Crystal Display module with LED Backlight unit and 4ch-LVDS interface. This
module supports 1920 x 1080 Full HDTV format and can display 16.7M colors (8-bit). The converter module for
backlight is built-in.
1.2 FEATURES
Ё High brightness (400 nits)
Ё High contrast ratio (1000 :1)
Ё Fast response time (3ms)
Ё High color saturation (NTSC 72%)
Ё Full HDTV (1920 x 1080 pixels) resolution, true HDTV format
Ё DE (Data Enable) only mode
Ё LVDS (Low Voltage Differential Signaling) interface
Ё Optimized response time for 120 Hz frame rate
Ё Viewing Angle : 160°(H)/150°(V) (CR>10) TN Technology
1.3 APPLICATION
Ё TFT LCD TVs
Ё Optimized Brightness, Multi-Media Displays
1.4 GENERAL SPECIFICATIONS
Item
Specification
Unit Note
Active Area
Bezel Opening Area
698.4(H) x 392.85(V)
705.4(H) x 399.8 (V)
mm
(1)
mm
Driver Element
a-si TFT active matrix
--
Pixel Number
1920x R.G.B. x 1080
pixel -
Pixel Pitch(Sub Pixel)
0.12125 (H) x 0.36375 (V)
mm -
Pixel Arrangement
RGB vertical stripe
--
Power consumption
(65) Watt (2)
Display Colors
16.7M
color -
Display Operation Mode
Transmissive mode / Normally White
--
Surface Treatment
Anti-Glare coating (Haze 25%)
- (3)
Note (1) Please refer to the attached drawings in chapter 9 for more information about the front and back outlines.
Note (2) Please refer sec 3.1 and 3.2 for more information of Power consumption
Note (3) The spec. of the surface treatment is temporarily for this phase. CMI reserves the rights to change this feature.
Version 1.3
5 DateΚ11 Feb., 2011
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
5 Page 
Global LCD Panel Exchange Center
www.panelook.com
PRODUCT SPECIFICATION
3.2 BACKLIGHT CONNECTOR PIN CONFIGURATION
3.2.1 LED LIGHT BAR CHARACTERISTICS (Ta = 25 ± 2 ºC)
The backlight unit contains 2 pcs of light bars
Parameter
Symbol
Min.
Value
Typ.
Max.
Unit
Note
Total Current (8 String)
One String Current
One String Voltage
One String Voltage Variation
Life time
If
IL(2D)
IL(3D)
VW
ϦVW
-
-
-
-
39
-
30,000
1040
130
260
-
-
-
1102.4
137.8
275.6
47.45
2
-
mA
mA
mApeak 3D ENA=ON
VDC IL =130mA
V
Hrs (1)
Note (1) The lifetime is defined as the time which luminance of the LED decays to 50% compared to the
initial value, Operating condition: Continuous operating at Ta = 25±2к, IL =130mA.
3.2.2 CONVERTER CHARACTERISTICS (Ta = 25 ± 2 ºC)
Parameter
Symbol
Power Consumption
Converter Input Voltage
PBL(2D)
PBL(3D)
VBL
Min.
-
-
22.8
Value
Typ.
(50)
(24.0)
24.0
Max.
(57.5)
(27.6)
25.2
Unit
W
W
VDC
Note
(1), (2)
IL = 130 mA
(1), (2)
IL=2*typ.
Converter Input Current
Input Inrush Current
Dimming Frequency
IBL(2D)
IBL(3D)
IR(2D)
IR(3D)
FB
-
-
-
-
150
(2.08)
(1.0)
-
-
160
(2.4)
(1.15)
(3.24)
(6.67)
170
A Non Dimming
A
Apeak
VBL=22.8V,(IL=typ.)
(3), (7)
Apeak
VBL=22.8V,(IL=2*typ.)
(3), (6)
Hz (5)
Minimum Duty Ratio
DMIN
5
10
-%
(4), (5)
Note (1) The power supply capacity should be higher than the total converter power consumption PBL. Since
the pulse width modulation (PWM) mode was applied for backlight dimming, the driving current
changed as PWM duty on and off. The transient response of power supply should be considered for
the changing loading when converter dimming.
Note (2) The measurement condition of Max. value is based on 31.5" backlight unit under input voltage 24V,
average LED current 137.8mA at 2D Mode (LED current 275.6 mApeak at 3D Mode) and lighting 1
hour later.
Note (3) For input inrush current measurement, the VBL rising time from 10% to 90% is about 30ms.
Version 1.3
11 DateΚ11 Feb., 2011
The copyright belongs to CHIMEI InnoLux. Any unauthorized use is prohibited
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet V315HH6-LS1.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| V315HH6-LS1 | TFT LCD Module | CMI MEI |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |