|
|
PDF GP1U10X Data sheet ( Hoja de datos )
| Número de pieza | GP1U10X | |
| Descripción | Compact/ Surface Mount and Reflow Soldering Type IR Detecting Unit for Remote Control | |
| Fabricantes | Sharp Electrionic Components | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de GP1U10X (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
|
No Preview Available !
GP1U10X Series
GP1U10X Series
Compact, Surface Mount and
Reflow Soldering Type IR
Detecting Unit for Remote Control
s Features
1. Compact and surface mount type
(Mounting area : 4/5 compared with GP1U90X)
2. Reflow soldering type (240 ˚C, for 5 seconds or less)
3. Power filter capacitor and resistance are not required any more
as a result of adoption of built-in constant voltage circuit
4. Various B.P.F. (Band Pass Frequency) frequency to meet
different user needs
s Applications
1. Camera-integral VCRs
2. Mini components
s Package Style
Taped model on φ 330-mm reel (1500 pieces)
s Outline Dimensions
(Unit : mm)
(0.9)
Detector center
1 VCC
2 VOUT
3 GND
8.1 4 Case GND
g Dummy pattern
(GND potential)
3 - 0.9
2
g
1
3 - 0.9
3
g
4
6 - R0.4
3.75 3.75
* Pattern example viewed from PWB
Case GND terminal area
C0.5
2.2 5.7 2.2
area : Be careful not to pull
around the pattern.
* Tolerance : ± 0.3 mm
s Absolute Maximum Ratings
(Ta=25˚C)
Parameter
Supply voltage
*1Operating temperature
Storage temperature
*2Reflow soldering temperature
Symbol
V CC
Topr
Tstg
Tsol
Rating
0 to 6.3
- 10to+ 70
- 20to+ 70
240
Unit
V
˚C
˚C
˚C
*1 No dew condensation is allowed.
*2 Reflow soldering time : For 5 seconds
s Recommended Operating Conditions
Parameter
Supply voltage
Symbol Operating conditions Unit
VCC 4.7 to 5.3 V
“ In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs,
data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device.”
1 page  
GP1U10X Series
s Precautions for Operation
1) In case of adopting the infrared light detecting unit for the wireless remote control, use it in accordance
with the transmission scheme and the signal format recommended in "Countermeasures for malfunction prevention of
home appliances with remote control" issued from Japan Association of Electrical Home Appliances (AEHA) in July, 1987.
Use of a transmission scheme and a signal format different from those recommended may cause malfunction of home appliances.
(Example : signal format without leader signal, bit structure of small duty ratio (TH/(TH+T L)))
2) Use the light emitting unit (remote control transmitter), in consideration of performance, characteristics,
operating conditions of light light emitting device and the characteristics of t he light detecting unit.
3) Pay attention to a malfunction of the light detecting unit when the surface is stained with dust and refuse.
Care must be taken not to touch the light detector surface.
If it should be dirty, wipe off such dust and refuse with soft cloth so as to pr event scratch. In case some solvents are required,
use methyl alcohol, ethyl alcohol or isopropyl alcohol only.
Also, protect the light detecting unit against flux and others, since their deposition on the unit inside causes reduction of the function,
fading of markings such as the part number.
4) The shield case should be grounded on PWB pattern.
(The area across the shield case and the GND terminal is internally conductive in some cases and non-conductive in some other cases.)
5) Do not apply unnecessary force to the terminal and the case.
6) Do not push the light detector surface (photodiode) from outside.
7) To avoid the electrostatic breakdown of IC, handle the unit under the condition of grounding with human body, soldering iron, etc.
8) Do not use hole and groove set in the case of the light detecting unit for ot her purposes,
since they are required to maintain the specified performance.
5 Page | ||
| Páginas | Total 5 Páginas | |
| PDF Descargar | [ Datasheet GP1U10X.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| GP1U10X | Compact/ Surface Mount and Reflow Soldering Type IR Detecting Unit for Remote Control | Sharp Electrionic Components |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |