|
|
PDF M106-A9G Data sheet ( Hoja de datos )
| Número de pieza | M106-A9G | |
| Descripción | Contact Image Sensor Module | |
| Fabricantes | CMOS Sensor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de M106-A9G (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
|
No Preview Available !
Preliminary
Contact Image Sensor
(CIS) Module
Product Name
M106-A9G
Approval
Notes
CMOS Sensor Inc.
20045 Stevens Creek Blvd.,
Suite 1A
Cupertino, CA., 95014
Tel: (408) 366-2898
Fax: (408) 366-2698
Approved Checked Designed
Issued
August 25, 2005
Revision no. Rev. 1
All specifications of this device are subject to change without notice.
20045 Stevens Creek Blvd., Suite 1A, Cupertino, CA., 95014
Tel: (408) 366-2898, Fax: (408) 366-2698
1 page  
Electro-optical characteristics:
at f = 2 MHz, VDD = 5 V, Tint *(1) = 0.25 ms, λ*(2) = 550 nm, Ta*(3) = 25 °C
(unless otherwise noted)
symbol
Parameter
test conditions
min. typ max
Vp*(4) Analog output voltage at white paper O.D. *(11) = 0.05 ~ 0.1 2.8 3.0 3.2
Up*(5) White paper non-uniformity
O.D. = 0.05 ~ 0.1
-30
30
Upadj*(6) Adjacent pixel non-uniformity
O.D. = 0.05 ~ 0.1
-25
25
Vd*(7) Analog output voltage at dark paper light off, O.D. = 0.8
0.8
Ud*(8) Dark signal non-uniformity
light off, O.D. = 0.8
200
MTF*(9) Modulation transfer function
at 3.85 lp/mm*(12)
30
γ*(10)
Linearity
0.85 1.1
unit
V
%
%
V
mV
%
Definition:
1. Tint is an integration time. It is determined by the interval between two start pulses.
2. λ is a wavelength of the light source.
3. Ta is ambient temperature.
4. Vp = (Vpmax + Vpmin) / 2
where Vpmax is a maximum voltage of whole module on white document.
Vpmin is a minimum voltage of whole module on white document.
5. Up is a pixel - pixel photo response non-uniformity within whole module.
Up = [(Vpmax - Vpmin) / Vp] x 100%
6. Upadj = Max [|(Vp(i) - Vp(i+1)| / Vp(i)] x 100%
where Vp(i) is the video signal output of each pixel # i
Vp(i+1) is the video signal output of each pixel # (i+1)
7. Vd = (Vdmax + Vdmin) / 2
where Vdmax is a maximum dark signal on whole module.
Vdmin is a minimum dark voltage on whole module.
8. Ud = Vdmax - Vdmin
9. MTF = [(Vmax - Vmin) / (Vmax + Vmin)] x 100%
where Vmax is the maximum output voltage at 3.85 lp/mm document.
Vmin is the minimum output voltage at 3.85 lp/mm document.
10. γ = log[(V2-Vd) / (V1-Vd)] / log (E2/E1) or log [(V2 - Vd) / (V1 - Vd)] / log (T2/T1)
where V1 is the output voltage of E1 illumination or T1 integration time
V2 is the output voltage of E2 illumination or T2 integration time
at 10 ~ 90% of saturation conduction.
11. O.D. = optical density of the paper.
12. lp / mm = line pair per millimeter
20045 Stevens Creek Blvd., Suite 1A, Cupertino, CA., 95014
Tel: (408) 366-2898, Fax: (408) 366-2698
5 Page | ||
| Páginas | Total 10 Páginas | |
| PDF Descargar | [ Datasheet M106-A9G.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| M106-A9G | Contact Image Sensor Module | CMOS Sensor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |