DataSheet.es    


PDF T420HW02-V0 Data sheet ( Hoja de datos )

Número de pieza T420HW02-V0
Descripción Full-HD Color TFT-LCD Module
Fabricantes AUO 
Logotipo AUO Logotipo



Hay una vista previa y un enlace de descarga de T420HW02-V0 (archivo pdf) en la parte inferior de esta página.


Total 29 Páginas

No Preview Available ! T420HW02-V0 Hoja de datos, Descripción, Manual

Global LCD Panel Exchange Center
www.panelook.com
Document Version: 2.0
Date:2008/5/21
Product Functional Specification
42” Full-HD Color TFT-LCD Module
Model Name: T420HW02 V0
( ) Preliminary Specification
(*) Final Specification
Note : This specification is subject to change without notice.
©Copyright AU Optronics, Inc.
January, 2008 All Rights Reserved.
No Reproduction and Redistribution Allowed
T420HW02 V0
1/29
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com

1 page




T420HW02-V0 pdf
Global LCD Panel Exchange Center
www.panelook.com
2. Absolute Maximum Ratings
The following are maximum values which, if exceeded, may cause faulty operation or damage to the
unit.
Item
Symbol
Min
Max
Unit
Note
Power Supply Input Voltage
VDD -0.3
14
[Volt] 1
Logic Input Voltage
Vin -0.3 3.6 [Volt] 1
BLU Input Voltage
VDDB
-0.3
26.4
[Volt] 1
BLU Brightness Control Voltage BLON
-0.3
3.6
[Volt] 1
Ambient Operating
TOP 0 +50 [oC] 2
Temperature
Ambient Operating Humidity
Storage Temperature
HOP 10
80 [%RH] 2
TST -20 +60 [oC] 2
Storage Humidity
HST 10 80 [%RH] 2
Shock (non-operation)
- 50 G 3
Vibration (non-operation)
- 1.5
G4
Thermal shock
-20 60
C5
Note 1 : Duration = 50msec
кNote 2 : Maximum Wet-Bulb should be 50 and No condensation.
Note 3 : Half sine wave, shock level : 50G(11ms), direction : ±x, ±y, ±z (one time each direction)
Note 4 : Wave form : Random, vibration level : 1.5G RMS, Bandwidth : 10~500Hz
Duration : X,Y,Z 30min (one time each direction)
Note 5 : -20C/1hr ~ 60C/1hr, 100 cycles
©Copyright AU Optronics, Inc.
January, 2008 All Rights Reserved.
No Reproduction and Redistribution Allowed
T420HW02 V0
5/29
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com

5 Page





T420HW02-V0 arduino
Global LCD Panel Exchange Center
www.panelook.com
2. Input specification
Connector 1: S14B-PH-SM3-TB(JST) or equivalent
Pin No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Symbol
VDDB
VDDB
VDDB
VDDB
VDDB
BLGND
BLGND
BLGND
BLGND
BLGND
Det
VBLON
PDIM(2)
PDIM
Selection(3,4)
Description
Operating Voltage Supply, +24V DC regulated
Operating Voltage Supply, +24V DC regulated
Operating Voltage Supply, +24V DC regulated
Operating Voltage Supply, +24V DC regulated
Operating Voltage Supply, +24V DC regulated
Ground and Current Return
Ground and Current Return
Ground and Current Return
Ground and Current Return
Ground and Current Return
Output of Detect error: Low=NG , Open/High=OK
BL On-Off: Open/High (3.3V) for BL On as default
External PWM (AC Signal Control Duty);
Internal PWM (DC Power Control Duty, 0~3.3V);
Open/High (+3.3V, 100% Duty) for 100%
GND: External PWM dimming;
Open/High (3.3V): Internal PWM dimming.
Note (1)
Note (2)
Note (3)
Note (4)
Det is Output pin for detect power error.
PDIM is PWM duty control input for +3.3V TTL level signal or DC voltage by Pin 14 input.
This input signal is (a) continuous pulse signal with +3.3V, TTL level signal spec, or (b) DC
power with 0~3.3V. If this is Open or +3.3V, 100% duty (i.e. +3.3V, DC level), backlight
should perform 100% luminance. Duty ratio of this input signal should be proportional
relationship in certain range of control without any kind of inherent side effect like waterfall
effect on screen. Guaranteed duty range and dimming ratio should be specified with
supplementary measurement result.
Pin 14 is the selection pin for PWM control method; if this pin is connected to GND, PDIM
input of Pin 13 should have logic level duty signal for PWM control. If this is set to High or
Open, Pin 13 should have DC level signal therefore the Inverter should have Saw Tooth
Wave Generator to generate internal PWM signal. Default setting is “Not Connected”, Pin 13
of PWM control should have DC Level signal for PWM.
Pin 14 selection vs. Pin 11/13 control function table:
Pin 13
Default: Open/High: 100%
Pin 14 = GND
Pin 14 = Open/High
External PWM
(AC Signal Control Duty)
Internal PWM
(DC Power Control Duty)
©Copyright AU Optronics, Inc.
January, 2008 All Rights Reserved.
No Reproduction and Redistribution Allowed
T420HW02 V0
11/29
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com

11 Page







PáginasTotal 29 Páginas
PDF Descargar[ Datasheet T420HW02-V0.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
T420HW02-V0Full-HD Color TFT-LCD ModuleAUO
AUO
T420HW02-V1Full-HD Color TFT-LCD ModuleAUO
AUO

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar