DataSheet.es    


PDF TH72002 Data sheet ( Hoja de datos )

Número de pieza TH72002
Descripción ASK Transmitter
Fabricantes Melexis 
Logotipo Melexis Logotipo



Hay una vista previa y un enlace de descarga de TH72002 (archivo pdf) en la parte inferior de esta página.


Total 20 Páginas

No Preview Available ! TH72002 Hoja de datos, Descripción, Manual

TH72002
315MHz
ASK Transmitter
Features
! Fully integrated PLL-stabilized VCO
! Frequency range from 290 MHz to 350 MHz
! Single-ended RF output
! ASK achieved by on/off keying of internal
power amplifier up to 40 kbit/s
! Wide power supply range from 1.95 V to 5.5 V
! Very low standby current
! On-chip low voltage detector
! High over-all frequency accuracy
! Adjustable output power range from
-12 dBm to +11 dBm
! Adjustable current consumption from
3.2 mA to 10.3 mA
! Conforms to FCC part 15 and similar standards
! 8-pin Small Outline Integrated Circuit (SOIC)
Ordering Information
Part Number
Temperature Code
TH72002
K (-40°C to 125°C)
Package Code
DC (SOIC8)
Delivery Form
98 pc/tube
2500 pc/T&R
Application Examples
! General digital data transmission
! Tire Pressure Monitoring Systems (TPMS)
! Remote Keyless Entry (RKE)
! Wireless access control
! Alarm and security systems
! Garage door openers
! Remote Controls
! Home and building automation
! Low-power telemetry systems
Pin Description
ASKDTA 1
n. c. 2
ROI 3
ENTX 4
TH72002
8 VEE
7 OUT
6 VCC
5 PSEL
General Description
The TH72002 ASK transmitter IC is designed for applications in the 315 MHz industrial-scientific-medical
(ISM) band. It can also be used for any other system with carrier frequencies ranging from
290 MHz to 350 MHz.
The transmitter's carrier frequency fc is determined by the frequency of the reference crystal fref. The inte-
grated PLL synthesizer ensures that carrier frequencies, ranging from 290 MHz to 350 MHz, can be
achieved. This is done by using a crystal with a reference frequency according to: fref = fc/N, where N = 32 is
the PLL feedback divider ratio.
3901072002
Rev. 007
Page 1 of 20
Data Sheet
June/07

1 page




TH72002 pdf
TH72002
315MHz
ASK Transmitter
2.4 Output Power Selection
The transmitter is provided with an output power selection feature. There are four predefined output power
steps and one off-step accessible via the power selection pin PSEL. A digital power step adjustment was
chosen because of its high accuracy and stability. The number of steps and the step sizes as well as the
corresponding power levels are selected to cover a wide spectrum of different applications.
The implementation of the output power control
logic is shown in figure 3. There are two
matched current sources with an amount of
about 8 µA. One current source is directly ap-
plied to the PSEL pin. The other current source
is used for the generation of reference voltages
with a resistor ladder. These reference voltages
are defining the thresholds between the power
steps. The four comparators deliver thermome-
ter-coded control signals depending on the
voltage level at the pin PSEL. In order to have a
certain amount of ripple tolerance in a noisy
environment the comparators are provided with
a little hysteresis of about 20 mV. With these
control signals, weighted current sources of the
power amplifier are switched on or off to set the
desired output power level (Digitally Controlled
Current Source). The LOCK, ASK signal and
the output of the low voltage detector are gating
this current source.
RPS
PSEL
ASKDTA
&
&
&&&
OUT
Fig. 3: Block diagram of output power control circuitry
There are two ways to select the desired output power step. First by applying a DC voltage at the pin PSEL,
then this voltage directly selects the desired output power step. This kind of power selection can be used if
the transmission power must be changed during operation. For a fixed-power application a resistor can be
used which is connected from the PSEL pin to ground. The voltage drop across this resistor selects the de-
sired output power level. For fixed-power applications at the highest power step this resistor can be omitted.
The pin PSEL is in a high impedance state during the “TX standby” mode.
2.5 Lock Detection
The lock detection circuitry turns on the power amplifier only after PLL lock. This prevents from unwanted
emission of the transmitter if the PLL is unlocked.
2.6 Low Voltage Detection
The supply voltage is sensed by a low voltage detect circuitry. The power amplifier is turned off if the supply
voltage drops below a value of about 1.85 V. This is done in order to prevent unwanted emission of the
transmitter if the supply voltage is too low.
3901072002
Rev. 007
Page 5 of 20
Data Sheet
June/07

5 Page





TH72002 arduino
5 Typical Operating Characteristics
5.1 DC Characteristics
I SBY
5µA
4µA
3µA
2µA
1µA
200nA
Standby current
150nA
100nA
50nA
0
2.0 2.5 3.0 3.5 4.0 4.5
Vcc [V]
Fig. 5: Standby current limits
TH72002
315MHz
ASK Transmitter
125°C
85°C
25°C
5.0 5.5
6.0
power step 0
3.0
125°C
2.8 105°C
85°C
2.6
2.4 25°C
0°C
2.2
-20°C
2.0
-40°C
1.8
1.8 2.2 2.6 3.0 3.4 3.8 4.2 4.6 5.0 5.4 5.8
Vcc [V]
Fig. 6: Supply current in power step 0
3901072002
Rev. 007
Page 11 of 20
Data Sheet
June/07

11 Page







PáginasTotal 20 Páginas
PDF Descargar[ Datasheet TH72002.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
TH72001315MHz FSK TransmitterMelexis
Melexis
TH72002ASK TransmitterMelexis
Melexis
TH72005FSK/ASK TransmitterMelexis
Melexis
TH72006FSK/ASK TransmitterMelexis
Melexis

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar