DataSheet.es    


PDF GS9029-CTD Data sheet ( Hoja de datos )

Número de pieza GS9029-CTD
Descripción GENLINX GS9029 Quad Output Serial Digital Video Cable Driver
Fabricantes ETC 
Logotipo ETC Logotipo



Hay una vista previa y un enlace de descarga de GS9029-CTD (archivo pdf) en la parte inferior de esta página.


Total 8 Páginas

No Preview Available ! GS9029-CTD Hoja de datos, Descripción, Manual

GENLINX II GS9029 Quad Output
Serial Digital Video Cable Driver
FEATURES
• SMPTE 259M compliant
• four isolated outputs (two complimentary pairs),
adjustable from 50mV-1000mV into 75loads
• operational from 143Mb/s to 540Mb/s and beyond
• nominal 500ps rise/fall times
• precise ±7.5% output amplitudes
• 40% system power reduction over GS9007
• 75on-chip input termination resistors
• input hysteresis
• operational down to 80mV input amplitude
• superior output isolation
• "Bus Through" expansion port for fan out
requirements
APPLICATIONS
4ƒsc, 4:2:2 and 4:4:4:4 serial digital video co-axial
transmission interfaces from 143 to 540Mb/s; General
purpose cable driving applications (co-axial cable or UTP).
DESCRIPTION
DATA SHEET
The GS9029 is a second generation bipolar integrated
circuit designed to drive four 75co-axial cables.
The GS9029 features two pairs of complementary outputs
whose amplitude is controlled within ±7.5%. The output
signal levels are also adjustable from 50mVp-p up to
1000mVp-p with little change in other performance
parameters. The amplitude of the output stage is varied by
adjusting the RSET resistor value. The patented current
mode outputs ensure superior output return loss and
minimal over shoot. The rise/fall time circuitry allows wide
range operation and provides symmetrical balanced
outputs to reject power supply noise. In addition high output
isolation ensures that the cable driver outputs are not
affected by the performance or status of other outputs.
Operational with input amplitudes as low as 80mV, the
GS9029 provides a robust serial interface.
The GS9029 is packaged in a 16 pin narrow SOIC and
operates from a single +5 or -5 volt supply. Typical system
power consumption is 320mW which is 40% less than the
GS9007.
ORDERING INFORMATION
PART NUMBER
PACKAGE
GS9029-CKD
16 pin SOIC Narrow
GS9029-CTD
16 pin SOIC Tap
TEMPERATURE
0°C to 70°C
0°C to 70°C
RSET0
RSET1
SDI/T
SDI/T
SDI
SDI
BANDGAP REFERENCE & BIASING CIRCUIT
75 75
SDO0
SDO0
INPUT
DIFFERENTIAL
PAIR WITH
HYSTERESIS
OUTPUT STAGE &
RISE/FALL TIME
CONTROL CIRCUIT
SDO1
SDO1
BLOCK DIAGRAM
Revision Date: February 2000
Document No. 521 - 97 - 02
GENNUM CORPORATION P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3
Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 E-mail: [email protected]
www.gennum.com

1 page




GS9029-CTD pdf
TYPICAL PERFORMANCE CURVES (VS = 5V, TA = 25°C unless otherwise shown. Devices guard band tested to 70°C only.)
530
525
520
515
510
505
500
495
490
485
480
0
10 20 30 40 50 60
TEMPERATURE (˚C)
Fig. 1 Rise/Fall vs. Temperature
70 80
1.62
1.61
1.60
1.59
1.58
0
10 20 30 40 50 60 70 80
TEMPERATURE (˚C)
Fig. 2 Serial Data Output Level vs. Temperature
Fig. 4 540Mb/s Eye Diagram
40
35
30
25
360Mb/s
20 177Mb/s
143Mb/s
540Mb/s
15 270Mb/s
10
0
20 40 60
TEMPERATURE (˚C)
80
Fig. 5 Peak to Peak Additive Jitter vs. Temperature
Fig. 3 270Mb/s Eye Diagram
5
521 - 97 - 02

5 Page










PáginasTotal 8 Páginas
PDF Descargar[ Datasheet GS9029-CTD.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
GS9029-CTDGENLINX GS9029 Quad Output Serial Digital Video Cable DriverETC
ETC

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar