|
|
PDF P42L6A-T1 Data sheet ( Hoja de datos )
| Número de pieza | P42L6A-T1 | |
| Descripción | PDP Module | |
| Fabricantes | Haier | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de P42L6A-T1 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
-1-
Service Manual
Model: P42L6A-T1
Specifications & Design are subject to change without notice.
1 page  
-5-
charged at the moment of Power OFF, standing by for 1 minute is required in
order to touch the Device circuitry.
2) CAUTIONS
(1) Do not place this product in a location that is subject to heavy vibration, or
on an unstable surface such as an inclined surface. The product may fall off or
fall over causing injuries.
(2) Before disconnecting cable from the product, be sure to turn off the power.
Be sure to hold the connector when disconnecting cables. Pulling a cable with
excessive force may cause the core of the cable to be exposed or break the
cable, and this can lead to fire or electric shock.
(3) This product should be moved by two or more persons. If one person
attempts to carry this product alone, he/she may be injured.
(4) This product contains glass. The glass may break, causing injuries, if shock,
vibration, heat, or distortion is applied to the product.
(5) The temperature of the glass of the display may rise to 80°C or more
depending on the conditions of use If you touch the glass inadvertently, you
may be burned.
(6) If glass surface of the display breaks or is scratched, do not touch the
broken pieces or the scratches with bare hands. You may be injured.
(7) PDP Module requires to be handled with care not to be touched with metal
or hard materials, and must not be stressed by heat or mechanical impact.
(8) There are some exposed components on the rear panel of this product.
Touching these components may cause an electric shock.
(9) When moving the product, be sure to turn off the power and disconnect all
the cables. While moving the product, watch your step. The product may be
dropped or all leading to injuries of electric shock.
(10) In order to protect static electricity due to C-MOS circuitry of
the Drive part, wear a wrist band to protect static electricity
when handling.
(11) If cleaning the Panel, wipe it with a soft cloth moistened with water or a
neutral detergent and squeezed, being careful not to touch the connector part
of the Panel. And don’t use chemical materials like thinner or benzene.
(12) If this product is used as a display board to display a static image, “image
sticking” occurs. This means that the luminance of areas of the display that
remain lit for a long time drops compared with luminance of areas that are lit for
a shorter time, causing uneven luminance across the display The degree to
which this occurs is in proportion to the luminance at which the display is used.
To prevent this phenomenon, therefore, avoid static images as much as
possible and design your system so that it is used at a low luminance, by
reducing signal level difference between bright area and less bright area
through signal processing.
(13) Because PDP Module emits heat from the Glass Panel part and the Drive
circuitry, the environmental temperature must not be over 40°C.
The temperature of the Glass Panel part is especially high owing to heat from
5 Page 
b.Trouble shooting
- 11 -
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet P42L6A-T1.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| P42L6A-T1 | PDP Module | Haier |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |