|
|
PDF DD-1920-HDMI Data sheet ( Hoja de datos )
| Número de pieza | DD-1920-HDMI | |
| Descripción | HDMI INTERFACE CONTROLLER | |
| Fabricantes | Digital View | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de DD-1920-HDMI (archivo pdf) en la parte inferior de esta página. Total 31 Páginas | ||
|
No Preview Available !
HDMI INTERFACE CONTROLLER
FOR TFT PANEL
Model: DD-1920-HDMI
Part number: 41730010X-3
INSTRUCTIONS
CONTENTS
Page: 2. Introduction, How to Proceed, Usage Note, Disclaimer
3. System design – Diagram of a suggested system
4. Assembly notes – Important information about system elements
5. Connection & Operation – How to use the controller
9. Connectors, pinouts & jumpers – Essential connection information
16. Controller dimensions
17. Application notes
19. Troubleshooting
20. Specifications
21. Appendix I – Mode Support Table
22. Appendix II – RS-232 control protocols
26. Appendix III – Appendix III – DDC/CI support at HDMI port
27. Appendix IV - Mapping definition
28. Appendix V – DV remote control unit work for DD-1920-HDMI
30. Warranty, Caution & Limitation of Liability, Trademarks
31. Contact details
It is essential that these instructions are read and understood before connecting or
powering up this controller.
Page 1 of 31
1 page  
CONNECTION & OPERATION
CAUTION: Never connect or disconnect parts of the display system when the system is powered up as this may cause serious damage.
CONNECTION
Connection and usage is quite straight forward (it is useful to have the relevant connection diagram available at this time):
LCD panel & Inverter: Connect the inverter (if it is not built-in the panel) to the CCFT lead connector of the LCD panel.
LVDS type panels: Plug the LVDS signal cable direct to J3. Insert the panel end of the cable to the LCD panel connector.
Inverter & Controller: Plug the inverter cable to CNB1 and CNA1 (if necessary). Plug another end to the connector on the inverter.
Function switch & Controller: Plug the OSD switch mount cable to CNC1 on the controller board and another end to the OSD switch mount.
LED 1 : Plug in a 3-way with dual colour LED to connector LED1 on the controller board for indicating the controller status.
IR & Controller: Plug in a 3-way with IR sensor to connector IR1 on the controller board.
Jumpers : Check all jumpers are set correctly. Details referring the connection diagram.
Jumpers & Inverter & Panel voltage: Particularly pay attention to the settings of JA3, JB1, JB2, JB3. JB2 & JB3 are used for inverter control (read
inverter specification and information on the jumper table to define the correct settings). JA3 is used for panel voltage input (read panel specification
and information on the jumper table to define the correct settings).
HDMI cable : Plug the HDMI cable to the connector P3 on the controller board.
Audio output (Stereo) from HDMI : audio output port CN1 supports Stereo audio output (no amplification) from the HDMI audio source inputted. It
requires to select the audio port “Speakers” via OSD menu under “Sound” > “Output” OSD menu page.
Power supply & Controller: Plug the DC 12V power in to the connector PP2. You can consider to use DigitalView mating power cable P/N
426013800-3, 160mm.
Power on: Switch on the controller board and panel by using the OSD switch mount.
CAUTION: Never connect or disconnect parts of the display system when the system is powered up as this may cause serious damage.
Controller LED status (LED1) :
State
No signal & backlight off
No signal & backlight on
With signal & backlight on
LED color
RED
ORANGE
GREEN
General:
If you are using supplied cables & accessories, ensure they are correct for the model of panel and controller.
If you are making your own cables & connectors refer carefully to both the panel & inverter specifications and the section in this manual,
“Connectors, Pinouts & Jumpers” to ensure the correct pin to pin wiring.
OPERATION
Once the system has been connected and switched on there are a number of functions available to adjust the display image as summarized in
the following sections. The settings chosen will be saved for each mode independently.
Page 5 of 31
5 Page 
DIP Switch selection – SW2
Pos #1 Pos #2 Pos #3 Pos.#4
Description
For WUXGA panel
OFF
OFF
OFF
OFF Samsung LTM220CS01
AU Optronics B170UW02 V0
ON OFF OFF OFF AU Optronics M215HW01
Samsung LTM230HT01
OFF
ON
OFF
OFF Samsung LTI400HA01
For UXGA panel
ON OFF OFF OFF NEC NL160120BC27-14
For WXGA panel
ON OFF OFF OFF Samsung LTA260W2-L01
ON
ON
OFF
OFF Samsung LTA460WS-L03
OFF
OFF
ON
OFF
Sharp LQ315T3LZ24 /
AU Optronics M156XW01 V0
ON OFF ON OFF LG LC420W02-A4
OFF
ON
ON OFF NEC NL12880BC20-02D
OFF
ON
OFF
OFF NEC NL12876BC26-21
ON ON
ON OFF AU Optronics M220EW01
For SXGA panels
ON OFF OFF
ON NEC NL128102BC29-01B
ON ON
ON OFF Fujitsu FLC48SXC8V
OFF
ON
OFF
ON Sharp LQ181E1LW31
ON ON OFF ON Samsung LTM170ET01
OFF
OFF
ON
ON AU Optronics M190EG01
For XGA panel
OFF
OFF
ON
ON AUO M150XN07 V2
OFF
ON
ON OFF LG LM151X2
ON ON OFF ON Sharp LQ150X1LGB1
Sharp LQ150X1LGN2A
ON OFF
ON
ON NEC NL10276BC12-02
OFF
ON
ON
ON NEC NL10276BC13-01C
ON ON ON ON NEC NL10276BC30-18/ 30-18C
NEC NL10276BC20-08
For SVGA panel
OFF
OFF
ON
OFF PrimeView PD104SL5H2
Sharp LQ121S1DG11
Sharp LQ104S1DG21
Sharp LQ121S1DG41
ON OFF ON OFF Toshiba LTM12C289
OFF
ON
ON OFF Sharp LQ084S3DG01
ON
ON
OFF
OFF Sharp LQ121S1LG41
NEC NL8060BC21-02
ON ON
ON OFF Sharp LQ104S1DG21
OFF
OFF
OFF
ON PrimeView PD104SL5
ON OFF OFF
ON NEC NL8060BH18-02
For WVGA panel
ON OFF ON OFF NEC NL8048BC19-02
ON OFF OFF
ON Sharp LQ070Y3LG4A
Others
ON OFF OFF
ON Samsung LTI430LA01
ON ON
ON OFF AU Optronics M200RW01 V1
ON OFF OFF OFF Sharp LQ150F1LH22
ON
ON
OFF
OFF Samsung LTM190M2-L31
ON OFF ON OFF LG LM171WX3-TLA1
OFF
ON
ON OFF LG LM171WX3
OFF
OFF
ON
OFF CPT CLAA102NA0ACW
For additional and recent added panels, please contact us to support.
Panel resolution
1920x1200
1920x1200
1920x1080
1920x1080
1920x1080
1600x1200
1366x768
1366x768
1366x768
1366x768
1280x800
1280x768
1680x1050
1280x1024
1280x1024
1280x1024
1280x1024
1280x1024
1024x768
1024x768
1024x768
1024x768
1024x768
1024x768
1024x768
1024x768
800x600
800x600
800x600
800x600
800x600
800x600
800x600
800x600
800x600
800x600
800x600
800x480
800x480
1920x480
1600x900
1400x1050
1440x900
1440x900
1440x900
1024x600
Page 11 of 31
11 Page | ||
| Páginas | Total 31 Páginas | |
| PDF Descargar | [ Datasheet DD-1920-HDMI.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| DD-1920-HDMI | HDMI INTERFACE CONTROLLER | Digital View |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |