DataSheet.es    


PDF RET012864C Data sheet ( Hoja de datos )

Número de pieza RET012864C
Descripción OLED Graphic 124x64 dots Display
Fabricantes Raystar 
Logotipo Raystar Logotipo



Hay una vista previa y un enlace de descarga de RET012864C (archivo pdf) en la parte inferior de esta página.


Total 1 Páginas

No Preview Available ! RET012864C Hoja de datos, Descripción, Manual

Raystar Optronics,Inc.
Mechanical Data
Item
Module dimension
View Area
Active area
Mounting hole
Dot Size
Dot Pitch
Dimension
89.7 × 47.2 × 3.4
63.41 x 32.69
61.41 × 30.69
82.7 × 40.2
0.45 × 0.45
0.48 × 0.48
Absolute Maximum Rating
Parameter
Symbol
Supply Voltage for Logic VDD
Supply Voltage for Display VCC
Min
-0.3
8
Max
3.5
16
Unit
mm
mm
mm
mm
mm
mm
Unit Notes
V 1, 2
V 1, 2
Electronical Characteristics
Characteristics Symbol Conditions Min Typ Max Unit
Supply Voltage
for Logic
Supply Voltage
for Display
VDD
VCC
- 2.4 2.7 3.5 V
-
14.5 15
15 V
High Level Input
VIH
IOUT= 100μA,
3.3MHz
0.8×VDD
-
VDD V
Low Level Input
IOUT= 100μA,
VIL 3.3MHz 0
- 0.2×VDD V
High Level
Output
IOUT= 100μA,
VOH 3.3MHz 0.9×VDD
-
VDD V
Low Level
lutput
VOL
IOUT= 100μA,
3.3MHz
Operating
Current for VDD
IDD
Note 4
Note 5
Operating
Current for VCC
ICC
Note 4
Note 5
Sleep Mode
Current for VDD
IDD, SLEEP
0
-
-
-
-
-
- 0.1×VDD V
250 400 μA
250 400 μA
31 39 mA
53 66 mA
- 10 μA
Sleep Mode
Current for VCC
ICC, SLEEP
- - 10 μA
Note 3: Brightness (Lbr) and Supply Voltage for Display (VCC) are subject to the change
of the panel characteristics and the customer’s request.
Note 4: VDD = 2.7V, VCC = 15V, 50% Display Area Turn on.
Note 5: VDD = 2.7V, VCC = 15V, 100% Display Area Turn on.
4.795
5.795
89.700±0.2
82.700±0.2
73.00±0.2
63.41(VA)
61.41(AA)
Active Area
128*64
Pixels
Feature
1. 128 x 64 dots
4. 1/64 duty cycle
2. Built-in Controller SSD1305T7R1 5. Interface: 6800, 8080, SPI, I2C
3. +3V power supply
6. Polarizer optional
Pin NO. Symbol
1 VCC
2 VCOMH
3 IREF
4~11 D7~D0
12 E/RD#
13 R/W#
14 D/C#
15 RES#
16 CS#
17 BS2
18 BS1
19 VDD
20 NC
21 VSS
22 VSS
Description
Power supply for analog circuit.
Com Voltage Output. A capacitor should be connected
between this pin and VSS.
Reference current input pin.
A resistor should be connected between this pin and
VSS.
Data bus.
Data read operation is initiated when it’s pull low.
Data write operation is initiated when it’s pull low.
Data/ Command control.
Pull high for write/read display data.
Pull low for write command or read status.
Reset signal input.
When it’s low, initialization of SSD1305 is executed.
Chip select input.
Communicating Protocol Select
These pins are MCU interface selection input. See the
following table:
68XX-parallel 80XX-parallel Serial
BS1 0
10
BS2 1
10
Power supply for logic circuit.
No connection.
Ground.
Ground.
OLED Graphic
type
RET012864C OLED Graphic 128x64 dots
Dimension drawing
3.400
2.0MAX
View Direction
1 22
W=0.3
0.5 P0.5*21=10.5
11.5±0.2
Scale 1:2
ICSSD1305T7
1
36.500
14.50
28.00
Ø3.2
Ø7.0
31
Single Tape Teraoka 631S
27*8*0.085mm
Double Tape Tesa 4972
22*6*0.05mm
0.48
0.45
Detail DOTS
Scale 1:10
2-Ø1.0
1 22
11.50
CONTCT SIZE
0.3±0.05
191
Raystar

1 page





PáginasTotal 1 Páginas
PDF Descargar[ Datasheet RET012864C.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
RET012864COLED Graphic 124x64 dots DisplayRaystar
Raystar
RET012864DDisplay ModuleRaystar
Raystar
RET012864EOLED Graphic 124x64 dots DisplayRaystar
Raystar
RET012864EYPP3N00000OLED ModuleRaystar
Raystar

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar