DataSheet.es    


PDF EMH7021-00FF10NRR Data sheet ( Hoja de datos )

Número de pieza EMH7021-00FF10NRR
Descripción 500KHz PWM Synchronous Boost Converter
Fabricantes Elite Semiconductor 
Logotipo Elite Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de EMH7021-00FF10NRR (archivo pdf) en la parte inferior de esta página.


Total 16 Páginas

No Preview Available ! EMH7021-00FF10NRR Hoja de datos, Descripción, Manual

ESMT/EMP
EMH7021
1A, 500KHz PWM Synchronous Boost Converter
with Output Isolated During Shutdown
General Description
The EMH7021 is a high efficiency, synchronous fixed
frequency, current-mode step-up DC/DC converter.
During shutdown mode, the output is completely
isolated from the input without drawing any battery
current. The fixed 500KHz switching frequency obtains
maximum efficiency up to 96% and uses only a few
external components.
With 150Ω loading, the minimum start-up voltage
can be as low as 0.93V, provided by a one or
two-cell alkaline or one-cell Li-Lon battery.
The features of EMH7021 include current limit, low
battery comparator, open-drain power good output,
short circuit, and thermal shutdown protection. The
EMH7021 is also available in 3X3mm TDFN-10
package.
Applications
Mobile Phone
Digital Still Cameras
Portable applications
MP3 Players
GPS Receivers
Features
Up to 96% efficiency
Reference voltage: 0.5V
Output to input disconnect at shutdown mode
Current delivery
- 1A@VOUT=3.3V, VBAT=2.4V
- 1A@VOUT=5.0V, VBAT=3.6V
Switch current limit protection
500KHz fixed switching frequency
Thermal shutdown protection
0.5V Low-battery comparator
Min-start up voltage: 0.93V
Low quiescent current: 48uA (Tpy.)
Low shutdown current < 1uA
TDFN 3x3mm 10 pins package
Typical Application
Elite Semiconductor Memory Technology Inc./Elite MicroPower Inc.
Publication Date: May 2012
Revision: 1.1
1/16

1 page




EMH7021-00FF10NRR pdf
ESMT/EMP
EMH7021
Note 1: Absolute Maximum ratings indicate limits beyond which damage may occur.
Note 2: All voltages are in respect to the potential of the ground pin.
Note 3: θJA is measured in the natural convection at TA=25on a highly effective thermal conductivity test board (2
layers, 2S0P).
Note 4: θJC represents the thermal resistance between the chip and the top of the package case.
Note 5: Maximum Power dissipation for the device is calculated using the following equation:
PD
TJ(MAX)
θJA
-
TA
Where TJ(MAX) is the maximum junction temperature, TA is the ambient temperature, and θ JA is the
junction-to-ambient thermal resistance. For example, for the TDFN-10 packageθJA = 110°C/W, TJ (MAX) =
150°C and using TA = 25°C, the maximum power dissipation is 1.136W. The derating factor (-1/θJA) =
-9.09mW/°C. Below 25°C the power dissipation figure can be increased by 9.09mW per degree and similarly
decreased by this factor for temperatures above 25°C.
Note 6: Typical Values represent the most likely parametric norm
Elite Semiconductor Memory Technology Inc./Elite MicroPower Inc.
Publication Date: May 2012
Revision: 1.1
5/16

5 Page





EMH7021-00FF10NRR arduino
ESMT/EMP
EMH7021
Inductor Selection
The Inductor is required to force the output voltage higher while being driven by a lower input voltage. For most
applications, a 6.8uH inductor is used. An inductor with higher peak inductor current tends to provide a higher
output voltage ripple (IPEAK * output filter capacitor ESR). The inductor’s DC resistance can significantly affect
efficiency. The maximum output current can be calculated as follows:
I OUT(max)
VBAT
VOUT
[ICL
Toff(
VOUT
2
VBAT
L
)]η
(2)
IOUT(max) Maximum loading
VBAT Input voltage
L Inductor value in μH
η efficiency (~ 0.9 typically)
Toff LX switch's off - time in μs
ICL 2.3A
VENDOR
Sumida
EPCOS
WURTH ELEKTRONIK
CYNTEC CO.
COILCRAFT
SERIES
CDRH5D28R
B82462-G4
7447789
PCMC063T
PCMB063T
MSSZ260-682MLD
Table 2
VALUE
6.8μH
6.8μH
6.8μH
6.8μH
6.8μH
6.8μH
ISAT
1.5A
1.65A
2.75A
4.5A
4.5A
4.9A
DCR
37m
51m
44m
54m
43. 9m
23m
Input Capacitor Selection
A low ESR 10μF input capacitor is recommended to improve transient behavior and reduce the peak current
drawn from the battery. Ceramic capacitors are also a good choice for input decoupling and should be
located as close as possible to the device.
Output Capacitor Selection
The output ripple voltage relates with the peak inductor current and the output capacitor’s ESR. Multilayer
ceramic capacitors are an excellent choice as they have extremely low ESR. A 47μF output capacitor is
sufficient for most applications.
Elite Semiconductor Memory Technology Inc./Elite MicroPower Inc.
Publication Date: May 2012
Revision: 1.1
11/16

11 Page







PáginasTotal 16 Páginas
PDF Descargar[ Datasheet EMH7021-00FF10NRR.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
EMH7021-00FF10NRR500KHz PWM Synchronous Boost ConverterElite Semiconductor
Elite Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar