DataSheet.es    


PDF CT-24SX12F Data sheet ( Hoja de datos )

Número de pieza CT-24SX12F
Descripción Color Television Service Manual
Fabricantes Panasonic 
Logotipo Panasonic Logotipo



Hay una vista previa y un enlace de descarga de CT-24SX12F (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! CT-24SX12F Hoja de datos, Descripción, Manual

ORDER NO. MTNC020203A1
B5
Service Manual
Simplified
Color Television
Simplified Manual
(NA8MS)
Panasonic
Models
CT-24SX12F
CT-24SX12UF
CT-27SX12F
CT-27SX12UF
CT-27SX32F
CT-27SX32UF
Chassis
BP367
BP367
AP390
AP390
BP390
BP390
This simplified service manual is issued to add listed models CT-27SX12F/UF and CT-27SX32F/UF to the main
service manual order No. MTNC010527C1 (CT-27SX31E) and CT-24SX12F/UF models to simplified service manual
order number MTNC010837A1 (CT-24SX11E). A set of unique schematics, unique settings and a complete parts list
are included in this manual.
Please file and use this simplified service manual together with main service manual, order No. MTNC010527C1
(CT-27SX31E) and simplified service manual order number MTNC010837A1 (CT-24SX11E).
WARNING! This Service Manual is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to
service or repair the product or products dealt with in this Service Manual by anyone else could result in serious injury or death.”
The service technician is required to read and follow the “Safety Precautions” and “Important Safety Notice” in the Main Manual.
Copyright 2002 by Matsushita Electric Corporation of
America. All rights reserved. Unauthorized copying
® and distribution is a violation of law.

1 page




CT-24SX12F pdf
Service Notes
Note: These components are affixed with glue. Be careful not to break or damage any foil under the
component or at the pins of the ICs when removing. Usually applying heat to the component for a
short time while twisting with tweezers will break the component loose.
Leadless Chip Component
(surface mount)
Chip components must be replaced with identical chips
due to critical foil track spacing. There are no holes in
the board to mount standard transistors or diodes.
Some chips capacitor or resistor board solder pads
may have holes through the board, however the hole
diameter limits standard resistor replacement to 1/8
watt. Standard capacitor may also be limited for the
same reason. It is recommended that identical
components be used.
Chip resistor have a three digit numerical resistance
code - 1st and 2nd significant digits and a multiplier.
Example: 162 = 1600 or 1.6kresistor, 0 = 0(jumper).
Chip capacitors generally do not have the value
indicated on the capacitor. The color of the component
indicates the general range of the capacitance.
Chip transistors are identified by a two letter code. The
first letter indicates the type and the second letter, the
grade of transistor.
Chip diodes have a two letter identification code as per
the code chart and are a dual diode pack with either
common anode or common cathode. Check the parts
list for correct diode number.
Component Removal
1. Use solder wick to remove solder from component
end caps or terminal.
2. Without pulling up, carefully twist the component
with tweezers to break the adhesive.
3. Do not reuse removed leadless or chip
components since they are subject to stress
fracture during removal.
Chip Component Installation
1. Put a small amount of solder on the board
soldering pads.
2. Hold the chip component against the soldering
pads with tweezers or with a miniature alligator clip
and apply heat to the pad area with a 30 watt iron
until solder flows. Do not apply heat for more than
3 seconds.
TYPE
Chip Components
GRADE
c
SOLDER
CAPS
b
e
TRANSISTOR
COMMON
CATHODE
CAPACITOR
1ST DIGIT 2ND DIGIT
MULTIPLIER
=1600 = 1.6k
ANODES
MH DIODE
SOLDER
CAPS
RESISTOR
How to Replace Flat-IC
- Required Tools -
• Soldering iron
• De-solder braids
• Needle nose pliers
• Magnifier
• Wire cutters (sharp & small)
1. Cut the pins of a defective IC with wire cutters.
Remove IC from board. If IC is glued to the board,
heat the IC and release the IC. See Note above.
Flat IC
2. Using soldering iron and needle nose pliers
remove the IC pins from the board.
Soldering
Iron
3. Using de-soldering braid and soldering iron remove
solder from affected are on board (pads).
De-soldering
Braid
Soldering
Iron
4. Position the new Flat-IC in place (apply the pins of
the Flat-IC to the soldering pads where the pins
need to be soldered). Determine the positions of
the soldering pads and pins by correctly aligning
the polarity symbol. Solder pin #1 first, align the IC.
Polarity
symbol
2nd solder
1st solder
Solder the pin opposite to pin #1. This will assist
positioning the IC.
5. Solder all pins to the soldering pads using a fine
tipped soldering iron.
Solder
Soldering
Iron
6. Check with a magnifier for solder bridge between
the pins or for dry joint between pins and soldering
pads. To remove a solder bridge, use a de-solder
braid as shown in the figure below.
-5-

5 Page





CT-24SX12F arduino
REPLACEMENT PARTS LIST
Models:CT-24SX12F/UF, CT-27SX12F/UF, CT-27SX32F/UF
Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing
any of these components use only manufacturer’s specified parts.
REF NO.
PART NO.
C961
C962
C963
C964
C966
C967
C968
C969
C971
ECA2AM100B
ECKW2H103ZF7
ECCR1H151J5
ECA1CHG101B
ECA1CHG101B
ECA1CM221B
ECKR1H103ZF5
ECKR1H103ZF5
TACCW222T50V
C1801 TCJ2VF1H103Z
C1802
C1803
C1804
C1805
ECQV1H154JL3
ECA1HMR22B
ECEA1HKAR22B
TCJ2VF1H333Z
C1806
C1807
C1808
C1809
C1810
TCJ2VF1H103Z
ECA1CM470B
TCJ2VF1H103Z
ECA1CM470B
TCJ2VF1H104Z
C1811 TCJ2VF1H103Z
C1812 TCJ2VF1H103Z
C1813
C1814
C1815
TCJ2VF1H103Z
ECA1CM470B
TCJ2VF1H104Z
C1816 TCJ2VF1H103Z
C1817
C1818
C1819
C1820
C1821
TCJ2VF1H103Z
ECA1CM100B
TCJ2VF1H104Z
ECA1CM470B
TCJ2VC1H150J
C1822 TCJ2VC1H120J
C1823 TCJ2VC1H680J
C1826 TCJ2VF1H103Z
C1827 TCJ2VF1H103Z
C1828
C1829
TCJ2VF1H103Z
TCJ2VF1H104Z
DESCRIPTION
CAP,E 10UF-100V
CAP,C .01UF-Z-500V
CAP DISC 150-5-50V
CAP,E 100UF-16V
CAP,E 100UF-16V
CAP,E 10UF-16V
CAP,C .01UF-Z-50V
CAP,C .01UF-Z-50V
CAP,C 2200PF/50V
CAP,C .01UF-Z-50V
CT-27SX32F/UF
CAP,P.15UF-J-50V
CT-27SX32F/UF
CAP,E .22UF-50V CT-27SX32F/UF
CAP,E .22UF-50V CT-27SX32F/UF
CAP,C .033UF-Z-50V
CT-27SX32F/UF
CAP,C .01UF-Z-50V
CT-27SX32F/UF
CAP,E 47UF/16V CT-27SX32F/UF
CAP,C .01UF-Z-50V
CT-27SX32F/UF
CAP,E 47UF/16V, CT-27SX32F/UF
CAP,C .1UF-Z-50V
CT-27SX32F/UF
CAP,C .01UF-Z-50V
CT-27SX32F/UF
CAP,C .01UF-Z-50V
CT-27SX32F/UF
CAP,C .01UF-Z-50V
CT-27SX32F/UF
CAP,E 47UF/16V CT-27SX32F/UF
CAP,C .1UF-Z-50V
CT-27SX32F/UF
CAP,C .01UF-Z-50V
CT-27SX32F/UF
CAP,C .01UF-Z-50V
CT-27SX32F/UF
CAP,E 10UF-16V CT-27SX32F/UF
CAP,C .1UF-Z-50V
CT-27SX32F/UF
CAP,E 47UF/16V CT-27SX32F/UF
CAP,C 15PF-J-50V
CT-27SX32F/UF
CAP,C 12PF-J-50V
CT-27SX32F/UF
CAP,C 68PF-J-50V
CT-27SX32F/UF
CAP,C .01UF-Z-50V
CT-27SX32F/UF
CAP,C .01UF-Z-50V
CT-27SX32F/UF
CAP,C .01UF-Z-50V
CT-27SX32F/UF
CAP,C .1UF-Z-50V CT-27SX32F/UF
REF NO.
PART NO.
C1830 TCJ2VC1H560J
C1831 TCJ2VF1H104Z
C1832 TCJ2VF1H104Z
C1833
C1835
C1836
TCJ2VF1H104Z
ECA1CM100B
TCJ2VC1H680J
C1837 TCJ2VF1H104Z
C1839 TCJ2VC1H680J
C1840 TCJ2VC1H680J
C2105
C2106
C2108
C2109
C2111
C2114
C2115
C2116
ECA0JM101B
ECA1HMR47B
ECA1CM330B
TCJ2VF1H103Z
ECEA1HFSR22B
TCJ2VF1H103Z
ECA1HM100B
TCJ2VF1H103Z
C2118 TCJ2VC1H270J
C2119
C2120
C2121
TCJ2VF1H103Z
ECEA1HFSR47B
TCJ2VF1H103Z
C2123 TCJ2VC1H270J
C2124
C2125
C2126
C2202
C2203
C2204
C2205
C2206
C2207
C2208
C2209
C2210
C2211
C2212
C2215
C2218
C2220
TCJ2VF1H103Z
ECA1CM100B
ECA1HMR22B
ECA1HM2R2B
ECA1HM4R7B
AP106K016CAE
ECA1HM010B
ECQB1H223JF3
AP335K016CAE
TCJ2VB1C104K
TCJ2VB1C104K
TCJ2VB1C104K
ECA1CM100B
ECQB1H473JF3
ECA0JM101B
ECA1HMR47B
TCJ2VC1H100D
DESCRIPTION
CAP,C 56PF-J-50V, CT-27SX32F/UF
CAP,C .1UF-Z-50V
CT-27SX32F/UF
CAP,C .1UF-Z-50V
CT-27SX32F/UF
CAP,C .1UF-Z-50V
CT-27SX32F/UF
CAP,E 10UF-16V, CT-27SX32F/UF
CAP,C 68PF-J-50V
CT-27SX32F/UF
CAP,C .1UF-Z-50V
CT-27SX32F/UF
CAP,C 68PF-J-50V
CT-27SX32F/UF
CAP,C 68PF-J-50V
CT-27SX32F/UF
CAP,E 100UF-6.3V
CT-27SX32F/UF
CAP,E .47UF-50V CT-27SX32F/UF
CAP,E 33UF-16V CT-27SX32F/UF
CAP,C .01UF-Z-50V
CT-27SX32F/UF
CAP,E .22UF-50V, CT-27SX32F/UF
CAP,C .01UF-Z-50V
CT-27SX32F/UF
CAP,E 10UF/50V, CT-27SX32F/UF
CAP,C .01UF-Z-50V
CT-27SX32F/UF
CAP,C 27PF-J-50V
CT-27SX32F/UF
CAP,C .01UF-Z-50V
CT-27SX32F/UF
CAP,E .47UF-50V, CT-27SX32F/UF
CAP,C .01UF-Z-50V
CT-27SX32F/UF
CAP,C 27PF-J-50V
CT-27SX32F/UF
CAP,C .01UF-Z-50V
CT-27SX32F/UF
CAP,E 10UF-16V CT-27SX32F/UF
CAP,E .22UF-50V CT-27SX32F/UF
CAP,E 2.2UF-50V
CAP,E 4.7UF-50V
CAP,T 10UF/16V
CAP,E 1UF-50V
CAP,P .022UF-J-50V
CAP,T 3.3UF/16V
CAP,C .1UF-K-16V
CAP,C .1UF-K-16V
CAP,C .1UF-K-16V
CAP,E 10UF-16V
CAP,P .047UF-J-50V
CAP,E 100UF-6.3V
CAP,E .47UF-50V
CAP,C 10PF-J-50V
050-02
- 11 -
Parts List

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet CT-24SX12F.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
CT-24SX12FColor Television Service ManualPanasonic
Panasonic
CT-24SX12UFColor Television Service ManualPanasonic
Panasonic

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar