|
|
Número de pieza | V23086-C1002-A803 | |
Descripción | PCB Single Relays | |
Fabricantes | Tyco | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de V23086-C1002-A803 (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
No Preview Available ! Automotive Relays
PCB Single Relays
Micro Relay K (THT – THR)
n Small power relay
n Limiting continuous current 30A
n Low weight
n Low noise operation
n Wave (THT) and reflow (THR/pin-in-paste) solderable versions
Typical applications
Car alarm, door control, door lock, heated front/rear screen, immobilizer,
lamps front/rear/fog light, interior lights, seat control, sun roof, window
lifter, wiper control.
Contact Data
Typical applications
Contact arrangement
Rated voltage
Rated current
Limiting continuous current
23°C
85°C
Limiting making current
Limiting breaking current
Contact material
Min. recommended contact load
Initial voltage drop at 10A, typ./max.
Operate/release time
Electrical enduranc
cyclic temperature -40°C, +25°C, +85°C
form C contact (CO) at 14VDC
Resistive/inductive load
V23086-*1*01-A403
1 form C, 1 CO
12VDC
NO/NC
30/25A
30/25A
20/15A
40A1)
30A
motor reverse blocked,
25A, 0.77mH
>1x105 ops.
form A contact (NO) at 14VDC
resistive 20A
>3x105 ops.
Wiper load
V23086-*1*02-A803
1 form C, 1 CO
10VDC
NO/NC
30/25A
30/25A
20/15A
40A1)
30A
AgSnO2
1A at 5VDC3)
30/300mV
typ. 3/1.5ms4)
wiper,
25A make/5A break,
generator peak,
20A on NC,1mH
>1x106 ops.
Mechanical endurance
>5x106 ops.
086C/R1_fcw1b
Resistive/inductive load
V23086-*1*01-A402
1 form A, 1 NO
12VDC
30A
30A
20A
40A1)
30A
Lamp load5)
V23086-*1*51-A502
1 form A, 1 NO
12VDC
30A
30A
20A
100A2)
30A
resistive 20A
>3x105 ops.
lamp 100A inrush,
10A steady state
>1x105 ops.5)
Max. DC load breaking capacity
1) The values apply to a resistive or inductive load with suitable spark suppression and at
maximum 13.5VDC for 12VDC load voltages. For a load current duration of maximum
3s for a make/break ratio of 1:10.
2) Corresponds to the peak inrush current on initial actuation (cold filament).
3) See chapter Diagnostics of Relays in our Application Notes or consult the internet at
http://relays.te.com/appnotes/
4) Measured at nominal voltage without coil suppression unit. A low resistive suppression
device in parallel to the relay coil increases the release time and reducesthe lifetime
caused by increased erosion and/or higher risk of contact tack welding.
5) Be aware of using right polarity, see Terminal Assignment. Wrong polarity will reduce
endurance.
Load limit curve 1: arc extinguishes, during transit time (changeover contact).
Load limit curve 2: safe shutdown, no stationary arc (make contact).
Load limit curves measured with low inductive resistors verified for 1000 switching events.
10-2013, Rev. 1013
www.te.com
© 2011 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
1
http://www.Datasheet4U.com
1 page Automotive Relays
PCB Single Relays
Micro Relay K (THT – THR) (Continued)
Product code structure
Typical product code V23086 -C 1 001 -A 4 03
Type
V23086 Micro Relay K (THT – THR)
Terminal and enclosure
C PCB version THT, sealed
Design
1 Single relay
Coil
001 Standard (THT)
801 Standard (THR)
051 Lamp load (THT)
Contact type
A Single contact
Contact material index
4 AgSnO2 standard
5 AgSnO2 lamp load
Contact arrangement index
02 NO
R PCB version THR, vented
002 Sensitive (THT)
802 Sensitive (THR)
851 Lamp load (THR)
8 AgSnO2 wiper load
03 CO
Product code
Version
Design
Coil Contact
V23086-C1001-A402
PCB THT,
Single
Standard
Single
V23086-C1001-A403
cleanable
V23086-C1051-A502
Lamp load
V23086-C1002-A803
Sensitive
V23086-R1801-A402
PCB THR,
Standard
V23086-R1801-A403
vented
V23086-R1851-A502
Lamp load
V23086-R1802-A803
Sensitive
This list represents the most common types and does not show all variants covered by this datasheet.
Other types on request.
Cont. material
AgSnO2 (standard)
AgSnO2 (lamp)
AgSnO2 (lwiper)
AgSnO2 (standard)
AgSnO2 (lamp)
AgSnO2 (lwiper)
Arrangement
1 form A, 1 NO
1 form C, 1 CO
1 form A, 1 NO
1 form C, 1 CO
1 form A, 1 NO
1 form C, 1 CO
1 form A, 1 NO
1 form C, 1 CO
Part number
0-1393280-5
0-1393280-6
2-1904093-1
2-1414987-3
2-1904093-2
6-1414920-0
9-1904064-4
7-1414967-8
10-2013, Rev. 1013
www.te.com
© 2011 Tyco Electronics Corporation,
a TE Connectivity Ltd. company.
Datasheets and product specification ac-
cording to IEC 61810-1 and to be used only
together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
5
5 Page |
Páginas | Total 5 Páginas | |
PDF Descargar | [ Datasheet V23086-C1002-A803.PDF ] |
Número de pieza | Descripción | Fabricantes |
V23086-C1002-A803 | PCB Single Relays | Tyco |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |