|
|
PDF CDX-GT315C Data sheet ( Hoja de datos )
| Número de pieza | CDX-GT315C | |
| Descripción | Car Strero Service Manual | |
| Fabricantes | Sony | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de CDX-GT315C (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
http://www.xiaoyu163.com
QQ 37631515C0DX8-9G24T9381259C9
SERVICE MANUAL
US Model
Ver. 1.1 2007.03
Canadian Model
AEP Model
UK Model
E Model
• The tuner and CD sections have no adjustments.
AUDIO POWER SPECIFICATIONS (US MODEL)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
Model Name Using Similar Mechanism
CD Drive Mechanism Type
Optical Pick-up Name
CDX-GT310/GT360
MG-101TA-188//Q
DAX-25A
TEL 13942296513CD player section
Signal-to-noise ratio 120 dB
Frequency response 10 – 20,000 Hz
Wow and flutter
Below measurable limit
Tuner section
FM
Tuning range
FM tuning interval
US, Canadian model:
87.5 – 107.9 MHz
AEP, UK model:
87.5 – 108.0 MHz
E model:
87.5 – 108.0 MHz (at 50 kHz step)
87.5 – 107.9 MHz (at 200 kHz step)
E model:
50 kHz/200 kHz switchable
QQ 376315150 892498299SPECIFICATIONS
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio 67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo), 0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response 30 – 15,000 Hz
AM (US, Canadian model)
Tuning range
530 – 1,710 kHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
30 µV
– Continued on next page –
FM/AM COMPACT DISC PLAYER
US, Canadian Model
FM/MW/LW COMPACT DISC PLAYER
AEP, UK Model
FM/MW/SW COMPACT DISC PLAYER
www x aoy u163 com. i9-887-480-02 Sony Corporation
.
2007C04-1
eVehicle Division
E Model
© 2007.03
Published by Sony Techno Create Corporation
http://www.Datasheet4U.com
http://www.xiaoyu163.com
1 page  
http://www.xiaoyu163.com
CDX-GT315C
SECTION 1
• LOCATION OF CONTROLS
QQ 376315150 892498299•US,Canadianmodel
GENERAL
This section is extracted
from instruction manual.
Location of controls and basic operations
Main unit
12 3 4
56
78
OFF
EQ3
SEEK
CAT
BTM
PUSH SELECT
SOURCE
SEEK
AUX
MODE
DIM
DSPL
ALBM
12
REP SHUF
PAUSE
3 4 5 6 SCRL
9q; qa qs qdqfqg
qh
CDX-GT315C
qj
Card remote commander
RM-X151
1
4
qk
qf
OFF
ATT
SOURCE
SEL
MODE
+
–
DSPL
SCRL
w;
wa
qd
ws
qj
123
456
wd
ql
+
VOL
–
Refer to the pages listed for details. The
corresponding buttons on the card remote
commander control the same functions as those
on the unit.
A OFF button
To power off; stop the source.
B EQ3 (equalizer) button 9
To select an equalizer type (XPLOD,
VOCAL, EDGE, CRUISE, SPACE,
GRAVITY, CUSTOM or OFF).
C Volume control dial/select button 9
To adjust volume (rotate); select setup items
(press and rotate).
D SOURCE button
To power on; change the source (Radio/CD/
MD*1/AUX/SAT*2).
E Disc slot
Insert the disc (label side up), playback
starts.
F Display window
G AUX input jack 11
To connect a portable audio device.
H Z (eject) button
To eject the disc.
I BTM/CAT*2 button 8
To start the BTM function (press and hold).
J (front panel release) button 5
K SEEK –/+ buttons
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); reverse/fast-
forward a track (press and hold).
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
L Receptor for the card remote
commander
M MODE button 8, 11
To select the radio band (FM/AM); select the
SAT tuner band (mode)*2; select the unit*3.
N DSPL (display)/DIM (dimmer) button
8
To change display items (press); change the
display brightness (press and hold).
O RESET button (located behind the front
panel) 4
P Number buttons
CD/MD*1:
(1)/(2): ALBM –/+*4*5
To skip albums (press); skip albums
continuously (press and hold).
(3): REP 8
(4): SHUF 8
(6): PAUSE*6
To pause playback. To cancel, press
again.
Radio:
To receive stored stations (press); store
stations (press and hold).
Q SCRL (scroll) button 8
To scroll the display item.
The following buttons on the card remote
commander have also different buttons/functions
from the unit. Remove the insulation film before
use (page 4).
qk < (.)/, (>) buttons
To control CD/radio, the same as (SEEK)
–/+ on the unit.
ql VOL (volume) +/– button
To adjust volume.
w; ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
wa SEL (select) button
The same as the select button on the unit.
ws M (+)/m (–) buttons
To control CD, the same as (1)/(2)
(ALBM –/+) on the unit.
wd Number buttons
To receive stored stations (press); store
stations (press and hold).
*1 When an MD changer is connected.
*2 When the SAT tuner is connected.
*3 When a CD/MD changer is connected.
*4 When an MP3/WMA is played.
*5 If the changer is connected, the operation is
different, see page 11.
*6 When playing back on this unit.
Note
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless (SOURCE) on the unit is pressed, or a disc is
inserted to activate the unit first.
Tip
For details on how to replace the battery, see
“Replacing the lithium battery of the card remote
commander” on page 14.
TEL6 13942296513
QQ 376315150 892498299 7
• AEP, UK model
Location of controls and basic operations
Main unit
12 3
4
56
78
OFF
EQ3
SEEK
PTY
PUSH SELECT
SOURCE
SEEK
AUX
MODE
DIM
DSPL
ALBM
12
REP SHUF
PAUSE
3 4 5 6 AF/ TA
9q; qa qs qdqfqg
qh
CDX-GT315C
qj
Card remote commander
RM-X151
1
4
qk
qf
OFF
ATT
SOURCE
SEL
MODE
+
–
DSPL
SCRL
w;
wa
qd
ws
wd
123
456
wf
ql
+
VOL
–
Refer to the pages listed for details. The
corresponding buttons on the card remote
commander control the same functions as those
on the unit.
A OFF button
To power off; stop the source.
B EQ3 (equalizer) button 11
To select an equalizer type (XPLOD,
VOCAL, EDGE, CRUISE, SPACE,
GRAVITY, CUSTOM or OFF).
C Volume control dial/select button 11
To adjust volume (rotate); select setup items
(press and rotate).
D SOURCE button
To power on; change the source (Radio/CD/
MD*1/AUX).
E Disc slot
Insert the disc (label side up), playback
starts.
F Display window
K SEEK –/+ buttons
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); reverse/fast-
forward a track (press and hold).
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
L Receptor for the card remote
commander
M MODE button 8, 13
To select the radio band (FM/MW/LW);
select the unit*2.
N DSPL (display)/DIM (dimmer) button
8, 9
To change display items (press); change the
display brightness (press and hold).
O RESET button (located behind the front
panel) 4
P Number buttons
CD/MD*1:
(1)/(2): ALBM –/+*3*4
To skip albums (press); skip albums
continuously (press and hold).
(3): REP 8
(4): SHUF 8
(6): PAUSE*5
To pause playback. To cancel, press
again.
Radio:
To receive stored stations (press); store
stations (press and hold).
Q AF (Alternative Frequencies)/TA
(Traffic Announcement) button 9
To set AF and TA in RDS.
The following buttons on the card remote
commander have also different buttons/functions
from the unit. Remove the insulation film before
use (page 4).
qk < (.)/, (>) buttons
To control CD/radio, the same as (SEEK)
–/+ on the unit.
ql VOL (volume) +/– button
To adjust volume.
w; ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
wa SEL (select) button
The same as the select button on the unit.
ws M (+)/m (–) buttons
To control CD, the same as (1)/(2)
(ALBM –/+) on the unit.
wd SCRL (scroll) button 8
To scroll the display item.
wf Number buttons
To receive stored stations (press); store
stations (press and hold).
*1 When an MD changer is connected.
*2 When a CD/MD changer is connected.
*3 When an MP3/WMA is played.
*4 If the changer is connected, the operation is
different, see page 13.
*5 When playing back on this unit.
Note
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless (SOURCE) on the unit is pressed, or a disc is
inserted to activate the unit first.
Tip
For details on how to replace the battery, see
“Replacing the lithium battery of the card remote
commander” on page 16.
www.
G AUX input jack 12
To connect a portable audio device.
H Z (eject) button
To eject the disc.
xiaoy u163.I PTY(ProgramType)button 10
To select PTY in RDS.
J (front panel release) button 5
com
6
7
http://www.xiaoyu163.com
5
5 Page 
http://www.xiaoyu163.com
CDX-GT315C
QQ 376315150 892498299
*1
BUS AUDIO IN
from car antenna (aerial)
desde la antena del automóvil
L
R
BUS AUDIO OUT
IN REAR/SUB
*AUDIO OUT
REAR 2
Fuse (10 A)
Fusible (10 A)
3
Left
Izquierdo
Right
Derecho
AMP REM
Blue/white striped
Con rayas azules y blancas
Max. supply current 0.3 A
Corriente máx. de alimentación de 0,3 A
White
Blanco
White/black striped
Con rayas blancas y negras
Grey
Gris
Grey/black striped
Con rayas grises y negras
Left
Izquierdo
Green
Verde
Green/black striped
Con rayas verdes y negras
Right
Derecho
Purple
Morado
Purple/black striped
Con rayas moradas y negras
TEL 13942296513
Supplied with XA-C40
Suministrado con el XA-C40
REMOTE
IN
*3
Source selector
(not supplied)
Selector de fuente
(no suministrado)
Supplied with the CD/MD changer
Suministrado con el cambiador de CD/MD
XA-C40
BUS
CONTROL IN
2
Black
Negro
Blue
Azul
Red
Rojo
ANT REM
Max. supply current 0.1 A
Corriente máx. de alimentación de 0,1 A
*1 RCA pin cord (not supplied)
*2 AUDIO OUT can be switched SUB or
REAR. For details, see the supplied
Operating Instructions.
*3 Insert with the cord upwards.
*1 Cable con terminales RCA
(no suministrado)
*2 AUDIO OUT (Salida de audio) puede
cambiarse a SUB (Secundaria) o REAR
(Posterior). Para obtener información,
consulte el manual de instrucciones
suministrado.
1 *3 Insertar con el cable hacia arriba.
2
*1
*2
*3
4
Yellow
Amarillo
5
QQ 376315150 892498299
Connection diagram
Diagrama de conexión
1 To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
1 A una superficie metálica del automóvil
Conecte primero el cable de conexión a masa negro, y
después los cables amarillo y rojo de fuente de alimentación.
2 To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
Notes
• It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
• When your car has a built-in FM/MW/SW antenna (aerial)
in the rear/side glass, see “Notes on the control and power
supply leads.”
3 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
4 To the +12 V power terminal which is
energized in the accessory position of the
ignition switch
Notes
• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a
metal surface of the car first.
• When your car has a built-in FM/MW/SW antenna (aerial)
in the rear/side glass, see “Notes on the control and power
supply leads.”
5 To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
Notes on the control and power supply leads
• The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/MW/SW antenna (aerial) in the
rear/side glass, connect the power antenna (aerial) control
lead (blue) or the accessory power supply lead (red) to the
power terminal of the existing antenna (aerial) booster. For
details, consult your dealer.
• A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power supply lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
2 Al cable de control de la antena motorizada
o al cable de fuente de alimentación del
amplificador de señal de la antena
Notas
• Si no se dispone de antena motorizada ni de amplificador
de antena, o se utiliza una antena telescópica accionada
manualmente, no será necesario conectar este cable.
• Si el automóvil incorpora una antena de FM/MW/SW en el
cristal trasero o lateral, consulte “Notas sobre los cables
de control y de fuente de alimentación”.
3 A AMP REMOTE IN de un amplificador de
potencia opcional
Esta conexión es sólo para amplificadores. La conexión de
cualquier otro sistema puede dañar la unidad.
4 Al terminal de alimentación de +12 V que
recibe energía en la posición de accesorio
del interruptor de encendido
Notas
• Si no hay posición de accesorio, conéctelo al terminal de
alimentación (batería) de +12 V que recibe energía sin
interrupción.
Asegúrese de conectar primero el cable de conexión a
masa negro a una superficie metálica del automóvil.
• Si el automóvil incorpora una antena de FM/MW/SW en el
cristal trasero o lateral, consulte “Notas sobre los cables
de control y de fuente de alimentación”.
5 Al terminal de alimentación de +12 V que
recibe energía sin interrupción
Asegúrese de conectar primero el cable de conexión a masa
negro a una superficie metálica del automóvil.
Notas sobre los cables de control y de fuente de
alimentación
• El cable de control de la antena motorizada (azul) suministrará
cc de + 12 V cuando conecte la alimentación del sintonizador.
• Si el automóvil dispone de una antena de FM/MW/SW
incorporada en el cristal trasero o lateral, conecte el cable
de control de antena motorizada (azul) o el cable de fuente
de alimentación auxiliar (rojo) al terminal de alimentación
del amplificador de antena existente. Para obtener más
información, consulte a su distribuidor.
• Con esta unidad no es posible utilizar una antena motorizada
sin caja de relé.
Notes on speaker connection
Conexión para protección de la memoria
• Before connecting the speakers, turn the unit off.
Si conecta el cable de fuente de alimentación amarillo, el circuito
• Use speakers with an impedance of 4 to 8 ohms, and with
de la memoria recibirá siempre alimentación, aunque apague el
adequate power handling capacities to avoid its damage.
interruptor de encendido.
• Do not connect the speaker terminals to the car chassis, or
Notas sobre la conexión de los altavoces
connect the terminals of the right speakers with those of the
• Antes de conectar los altavoces, desconecte la alimentación
left speaker.
de la unidad.
• Do not connect the ground (earth) lead of this unit to the
• Utilice altavoces con una impedancia de 4 a 8 Ω con la
negative (–) terminal of the speaker.
capacidad de potencia adecuada para evitar que se dañen.
• Do not attempt to connect the speakers in parallel.
• No conecte los terminales de altavoz al chasis del automóvil,
• Connect only passive speakers. Connecting active speakers
ni conecte los terminales del altavoz derecho con los del
(with built-in amplifiers) to the speaker terminals may damage
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
www . xiaoy u163.amplifierareconnectedcorrectly.
izquierdo.
• No conecte el cable de conexión a masa de esta unidad al
terminal negativo (–) del altavoz.
• No intente conectar los altavoces en paralelo.
• Conecte solamente altavoces pasivos. Si conecta altavoces
activos (con amplificadores incorporados) a los terminales de
altavoz, puede dañar la unidad.
• Para evitar fallas de funcionamiento, no utilice los cables de
altavoz incorporados instalados en el automóvil si la unidad
comparte un cable negativo común (–) para los altavoces
derecho e izquierdo.
• No conecte los cables de altavoz de la unidad entre sí.
Nota sobre la conexión
Si el altavoz no está conectado correctamente, aparecerá
“FAILURE” en la pantalla. Si es así, compruebe la conexión del
altavoz.
com
http://www.xiaoyu163.com
11
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet CDX-GT315C.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| CDX-GT315C | Car Strero Service Manual | Sony |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |