DataSheet.es    


PDF S2E04 Data sheet ( Hoja de datos )

Número de pieza S2E04
Descripción Single & Dual Output DC/DC Converters
Fabricantes Minmax Technology 
Logotipo Minmax Technology Logotipo



Hay una vista previa y un enlace de descarga de S2E04 (archivo pdf) en la parte inferior de esta página.


Total 6 Páginas

No Preview Available ! S2E04 Hoja de datos, Descripción, Manual

www.DataSheet4U.com
S2E00 Series
1.5W, Ultra-High Isolation DIP, Single & Dual Output DC/DC Converters
Key Features
y Low Cost
y 8000VDC Isolation
y MTBF > 2,000,000 Hours
y 30mV P-P Ripple and Noise
y Input 5, 12 and 15VDC
y Output 5, 12, 15, {5, {12 and {15VDC
y Temperature Performance -40] to +85]
y Low Isolation Capacitance
y Low Leakage Current
y Meets EN60950 and EN60601-1
Minmax's S2E00 Model 1.5W DC/DC's are specially
designed to provide 30mA output ripple, continuous short
circuit in a low-profile 24-pin DIP package.
The series consists of 18 models with input voltages of
5V, 12V and 15VDC which offers regulated output voltages of
5V, 12V, 15V, {5V, {12V and {15VDC.
The -40] to +85] operating temperature range makes
it ideal for data communication equipments, mobile battery
driven equipments,distributed power systems,
telecommunication equipments, mixed analog/digital
subsystems, automatic test instrumentation and industrial
robot systems.
$
Low Cost
8000
VDC
I/O Isolation
Low Noise
Block Diagram
Single Output
+Vin
LC
Filter
-Vin
Bipolar
Push-Pull
Inverter
Dual Output
+Vo
+Vin
LC
Filter
-Vin
Bipolar
Push-Pull
Inverter
-Vo
+Vo
Com.
-Vo
1 MINMAX REV:0 2005/04 http://www.Datasheet4U.com

1 page




S2E04 pdf
www.DataSheet4U.com
S2E00 Series
Test Configurations
Input Reflected-Ripple Current Test Setup
Input reflected-ripple current is measured with a inductor
Lin (4.7uH) and Cin (220uF, ESR < 1.0[ at 100 KHz) to
simulate source impedance.
Capacitor Cin, offsets possible battery impedance.
Current ripple is measured at the input terminals of the
module, measurement bandwidth is 0-500 KHz.
To Oscilloscope
+Vin +Out
+
Battery
+ Lin
Cin
Current
Probe
DC / DC
Converter
-Vin -Out
Load
Peak-to-Peak Output Noise Measurement Test
Use a Cout 0.33uF ceramic capacitor.
Scope measurement should be made by using a BNC
socket, measurement bandwidth is 0-20 MHz. Position the
load between 50 mm and 75 mm from the DC/DC Converter.
+Vin
+Out
Single Output
DC / DC
Converter
-Vin -Out
Copper Strip
Cout
Scope
Resistive
Load
In applications where power is supplied over long lines and
output loading is high, it may be necessary to use a capacitor
at the input to ensure startup.
Capacitor mounted close to the power module helps
ensure stability of the unit, it is recommended to use a good
quality low Equivalent Series Resistance (ESR < 1.0[ at 100
KHz) capacitor of a 2.2uF for the 5V input devices, a 1.0uF for
the 12V input devices and a 0.47uF for the 15V devices.
+
DC Power
Source
-
+Vin
+ DC / DC
Converter
Cin
-Vin
+Out
-Out
Load
Output Ripple Reduction
A good quality low ESR 1.5uF capacitor connected as
colse as possible to the load is recommended.
+
DC Power
Source
-
+Vin
+Out
Single Output
DC / DC
Converter
-Vin -Out
Cout
Load
+Vin
+Out
Dual Output
DC / DC Com.
Converter
-Vin -Out
Copper Strip
Cout
Cout
Scope
Resistive
Load
Scope
+
DC Power
Source
-
+Vin
+Out
Dual Output
DC / DC Com.
Converter
-Vin -Out
Cout
Load
Design & Feature Considerations
Maximum Capacitive Load
The S2E00 series has limitation of maximum connected
capacitance at the output.
The power module may be operated in current limiting
mode during start-up, affecting the ramp-up and the startup
time.
For optimum performance we recommend 220uF
maximum capacitive load for each dual outputs and 470uF
capacitive load for single outputs.
The maximum capacitance can be found in the data sheet.
Input Source Impedance
The power module should be connected to a low
ac-impedance input source. Highly inductive source
impedances can affect the stability of the power module.
Thermal Considerations
Many conditions affect the thermal performance of the
power module, such as orientation, airflow over the module
and board spacing. To avoid exceeding the maximum
temperature rating of the components inside the power
module, the case temperature must be kept below 95°C.
The derating curves are determined from measurements
obtained in an experimental apparatus.
Position of air velocity
probe and thermocouple
15mm / 0.6in
50mm / 2in
Air Flow
DUT
5
MINMAX
REV:0 2005/04

5 Page










PáginasTotal 6 Páginas
PDF Descargar[ Datasheet S2E04.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
S2E00Single & Dual Output DC/DC ConvertersMinmax Technology
Minmax Technology
S2E01Single & Dual Output DC/DC ConvertersMinmax Technology
Minmax Technology
S2E02Single & Dual Output DC/DC ConvertersMinmax Technology
Minmax Technology
S2E03Single & Dual Output DC/DC ConvertersMinmax Technology
Minmax Technology

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar