|
|
Número de pieza | CD4000 | |
Descripción | Codoor Installation & User Manual | |
Fabricantes | Siemens | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de CD4000 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! Codoor CD3500
Codoor CD4000
Installation & User Manual
Fire Safety & Security Products
Siemens Building Technologies
Free Datasheet http://www.Datasheet4U.com
1 page CD3500 & CD4000 Installation and User manual
About this manual
This manual covers both the Scandinavian style (CD3500) and the
International style (CD4000) of the Codoor. In the scope of this manual
we will use the name Codoor (unless notified.)
Codoor - General
The Codoor, a complete code lock suitable for fitting to a single door,
incorporates an electronic code lock, a mechanical locking device and
a power unit in the same housing. Codoor may be fitted on most doors
with handle operated locks. See page 20-21 for more information. When
Codoor is fitted; the outside door handle is disengaged and may be
pressed down without opening the door. To open the door, a 4-digit
code has to be entered. The handle on the inside of the door is not
affected by Codoor, and works normally for people leaving the premises.
All programming, except for setting of the programming code, is
entered via the keypad (see figure). Besides the keys, the keypad
includes two LEDs, one green and one red.
GREEN - In programming mode, the green LED indicates that codes
etc. have been entered correctly. It also confirms each key
press in programming mode.
RED - In operating mode, the red LED confirms each key press.
In programming mode, the LED flashes slowly until a
command is entered. Then the LED flashes quickly.
123
1
456
2 789
0 #
Free Datasheet http://www.Datasheet4U.com
5 Page CD3500 & CD4000 Installation and User manual
11
Setting codes
With Codoor you can program up to 9 different codes (codes 01-09). Follow
these steps:
1. Press then enter the 6-digit
programming code. Finish by pressing
. The red LED will flash slowly,
accompanied by simultaneous sounding of the buzzer.
2. Press then enter the code number (01-09) you
want to program. Finish by pressing . The red LED
will flash faster.
3. Press then enter the desired 4-digit code.
Finish by pressing . The green LED will come
on for 2 seconds. To enter any additional
codes, repeat steps 3 and 4.
4. Exit programming mode by entering 00 . The
buzzer sounds a rising tone to confirm.
0 0
Note! The unit automatically switches out of programming mode
into operating mode if no key is pressed within 10 seconds.
Programming must be done while the red LED flashes and the
buzzer sounds.
Delete code
Proceed like this:
1. Press then enter the 6-digit
programming code. Finish by pressing
. The red LED will flash slowly,
accompanied by simultaneous sounding
of the buzzer.
2. Press #, then enter the code (01 - 09) you wish to
#
delete. Finish by pressing #. The green LED will come
#
on. If you wish to delete more than one code, repeat step 3 for each
code.
3. Exit programming mode by entering 00 . The
0 0
buzzer sounds a rising tone to confirm.
Free Datasheet http://www.Datasheet4U.com
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet CD4000.PDF ] |
Número de pieza | Descripción | Fabricantes |
CD4000 | Codoor Installation & User Manual | Siemens |
CD4000A | CMOS NOR Gate | RCA |
CD4000B | CMOS NOR Gate | RCA |
CD4000BMS | CMOS NOR Gate | Intersil Corporation |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |