|
|
PDF M190ETN01.0 Data sheet ( Hoja de datos )
| Número de pieza | M190ETN01.0 | |
| Descripción | TFT LCD Module | |
| Fabricantes | AUO | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de M190ETN01.0 (archivo pdf) en la parte inferior de esta página. Total 34 Páginas | ||
|
No Preview Available !
Product Specification
AU OPTRONICS CORPORATION
M190ETN01.0
( ) Preliminary Specification
( V ) Final Specification
Module
Model Name
19.0” Color TFT-LCD
M190ETN01.0
Customer
Date
Approved by
Note: This Specification is subject to
change without notice.
Approved by
Date
Howard Lee
Oct. 23, 2012
Prepared by
Vincent Chan Oct. 23, 2012
AU Optronics Corporation
document version 1.1
1
Free Datasheet http://www.Datasheet4U.com
1 page  
Product Specification
AU OPTRONICS CORPORATION
1 Handling Precautions
M190ETN01.0
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human
earth when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was
taken out from the container, do not press the center of LED light bar edge. Instead,
press at the far ends of the LED light bar edge softly. Otherwise the TFT Module may be
damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
tilt the Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT
Module even momentary. At designing the enclosure, it should be taken into
consideration that no bending/twisting forces are applied to the TFT Module from
outside. Otherwise the TFT Module may be damaged.
12) Small amount of materials having no flammability grade is used in the LCD module. The
LCD module should be supplied by power complied with requirements of Limited
Power Source (IEC60950 or UL1950), or be applied exemption.
13) Avoid touching COF position while doing mechanical design.
14) While storing modules as spares for a long time, the following precautions are
necessary:
Store modules in a dark place. Do not expose them to sunlight or fluorescent light.
Keep the temperature between 5°C and 35°C at normal humidity.
15) Pls avoid touching COF position while you are doing mechanical design.
16) When storing modules as spares for a long time, the following precaution is necessary:
Store them in a dark place. Do not expose the module to sunlight or fluorescent light.
Keep the temperature between 5℃ and 35℃ at normal humidity.
document version 1.1
5
Free Datasheet http://www.Datasheet4U.com
5 Page 
Product Specification
AU OPTRONICS CORPORATION
M190ETN01.0
2.3 Mechanical Characteristics
Item
Unit
Min.
Note
Compression Endurance
[Kgf]
2.5
1
Note 1: Test Method
The point is at a distance from right-downside 25mm x 25mm defined as the Start Point of
Measure Points, and the point is at a distance 25mm from left-side & around 10mm from
PCB defined as the End Point.
Align 50mm x 50mm block from Start Point on the Bezel Back, and the corners of each
block are Measure Points.
If the distance from the last block to each side of the End Point ≧ 25mm, add other blocks
to make sure that most area of Bezel Back can be measured.
PCB
10mm
End Point
25mm
≧25mm
≧25mm
50mm
The last block
50mm
25mm
Start Point
25mm
document version 1.1
11
Free Datasheet http://www.Datasheet4U.com
11 Page | ||
| Páginas | Total 34 Páginas | |
| PDF Descargar | [ Datasheet M190ETN01.0.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| M190ETN01.0 | TFT LCD Module | AUO |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |