|
|
Número de pieza | SF1102B | |
Descripción | 230 MHz SAW Filter | |
Fabricantes | RFM | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de SF1102B (archivo pdf) en la parte inferior de esta página. Total 1 Páginas | ||
No Preview Available ! SF1102B 230 MHz SAW Filter
PRELIMINARY
• Designed for WCDMA 3G IF Applications
• Quartz Temperature Stability
• Small Size
• Hermetic 7 x 5 mm Surface-Mount Case
See Associated Plots
Characteristic
Nominal Center Frequency
Passband
Insertion Loss at fc
1 dB Passband
3 dB Passband
Amplitude Ripple over fc ±2.0 MHz
Group Delay Variation over fc ±2.0 MHz
Rejection
fc-25 to fc-5.0
fc+5 to fc+25
Operating Temperature Range
Sym
fc
IL
BW1
BW3
GDV
TA
Min Typ Max
230.000
16 18.0
±2.0 ±2.2
±2.5
1.0
100 150
40
38
-20 +80
Units
MHz
dB
MHz
Notes
1
1, 2
dBP-P
nsP-P
dB
1, 2, 3
°C 1
Matching to Unbalanced 50 Ω
Case Style
Lid Symbolization (YY = year, WW = week) See note 4
External L-C
SMP-03 7 x 5 mm Nominal Footprint
RFM SF1102A-1 YYWW
Absolute Maximum Ratings
Rating
Maximum Incident Power in Passband
Max. DC voltage between any 2 terminals
Storage Temperature Range
Max Soldering Profile
Value Units
+10 dBm
30 VDC
-40 to +85 °C
235°C for 90 s
Electrical Connections
Connection Terminals
Port 1 Hot 10
Port 1 Gnd Return
Port 2 Hot
Port 2 Gnd Return
Case Ground
1
5
6
All others
Notes:
1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified
demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer.
2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is
dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details.
4. “LRIP” or “L” after the part number indicates “low rate initial production” and “ENG” or “E” indicates “engineering prototypes.”
5. The design, manufacturing process, and specifications of this filter are subject to change.
6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching
may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design.
7. US and international patents may apply.
8. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
9. ©Copyright 1999, RF Monolithics Inc.
10. Electrostatic Sensitive Device. Observe precautions for handling.
RF Monolithics, Inc.
4347 Sigma Road
Dallas, Texas 75244
USA
Phone: +1(972)233-2903
Fax: +1(972)387-8148
e-mail: [email protected]
Home page: www.rfm.com
European Sales Office
44 1963 251383
44 1963 251510
SF1102B.DOC 12/11/2000 D
Free Datasheet http://www.datasheetlist.com/
1 page |
Páginas | Total 1 Páginas | |
PDF Descargar | [ Datasheet SF1102B.PDF ] |
Número de pieza | Descripción | Fabricantes |
SF1102A-1 | 230 MHz SAW Filter | RFM |
SF1102B | 230 MHz SAW Filter | RFM |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |