|
|
Número de pieza | CA100 | |
Descripción | COMPACT CAL MANUAL | |
Fabricantes | Omega | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de CA100 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! COMPACT CAL
M-2911
Free Datasheet http://www.datasheet-pdf.com/
1 page Safety Precautions
Ths instrument is an IEC safety class I instrument (provided with a terminal for
protective grounding). The following general safety precautions must be observed
during all phases of operation, service and repair of this instrument. If this instrument is
used in a manner not specified in this manual, the protection provided by the instrument
may be impaired. Also, we assume no liability for the customer's failure to comply with
these requirements.
General definitions of safety symbols used on the instrument and in this
manual
To avoid injury, death of personnel or damage to the instrument, the operator must refer
to an explanation in the User's Manual.
This instrument is protected by double insulation.
DC (Direct current)
Ni-Cd
Recycle
Make sure to comply with the following safety precautions. Failure to do so
might result in a fatality or injury to personnel from such hazards as electrical
shock, or damage to the instrument.
WARNING
Prohibition of Using the Instrument in a Gaseous Environment
Do not operate the instrument in the presence of inflammable and
explosive gases or vapors. Operation of the instrument in such an
environment constitutes a safety hazard.
Necessity of Protective Grounding
Never cut off the internal or external protective grounding wire or
disconnect the wiring of protective grounding terminal. Doing so
poses a potential shock hazard.
Defect in Protection Feature
Do not operate the instrument if there is a defect in protective
grounding or fuses. Before commencing operation, always make
sure that the protection feature is fault-free.
External Connection
After making sure that grounding is properly carried out, connect
the protective grounding before connecting to the measurement or
control unit. If you need to touch the circuit, you must turn off the
switch and make sure that no voltage is generated.
4
Free Datasheet http://www.datasheet-pdf.com/
5 Page Front Panel
General View
The following functions can be selected:
Function
Averaging
Display hold
Description
Displays the results of moving averages of measured data. This is useful if the measured
data are unstable or poor due to noise. (See page 21.)
Halts updating of the displayed measured value.
• 24 V DC power supply
This is a floating output. Available up to 24 V/22 mA DC max.
• Communications function
Using this function, the instrument can be controlled or measured data can be
transferred to a personal computer via an RS-232-C interface (D-sub 9 pin). This
function also allows the output of setting information or measured data to an ESC/P-
support printer.
• Three-way power supply
Three types of power supply: AA cells, AC adapter (free selection of AC voltages,
optional), and Ni-Cd battery pack (optional) are available.
SOURCE
MEASURE
24V OUT
1 POWER
DCV
DCA
Ω
2 CHARGE
TC
RTD
FRQ
3 PULSE
SOURCE
DCV
DCA
Ω
COMPACT CAL
MEASURE
LCD screen
SOURCE
4 24V OUT
MEASURE
ON
5 FUNCTION
12345
FUNCTION
ZERO CLR
SOURCE
6 RANGE
ON
NEXTENTER 6 7 8 9 0
HOLD
RANGE
16
15
14
7 8 9 10 11
12 13
1 Power switch
Turns the power on and off.
2 Charging start key
Begins the charging of the Ni-Cd battery pack (optional).
3 Backlight key
Turns backlighting on and off.
Operation keys for generation
4 24 V DC power supply key
Turns the 24 V DC power supply on and off.
5 Function selection key
Selects one of the generation functions: voltage, current, resistance, thermocouple,
RTD, frequency, and pulse.
6 Range selection key
Selects the range for setting generation values. For thermocouple or RTD, selects
TC or RTD type.
10
Free Datasheet http://www.datasheet-pdf.com/
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet CA100.PDF ] |
Número de pieza | Descripción | Fabricantes |
CA10 | SURFACE MOUNT ESD SUPPRESSORS/ 8-Line CA10 | Littelfuse |
CA100 | COMPACT CAL MANUAL | Omega |
CA1004 | Micropower Voltage Reference | Calogic |
CA1021 | Cascadable Amplifier 10 to 1000 MHz | Tyco Electronics |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |