|
|
Número de pieza | OC200 | |
Descripción | Orthoceph Service Program Manual | |
Fabricantes | Instrumentarium | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de OC200 (archivo pdf) en la parte inferior de esta página. Total 42 Páginas | ||
No Preview Available ! Orthopantomograph® OP200 & OP200 D
Orthoceph® OC200 & OC200 D
Service Program Manual
5140241-100 rev 3
Free Datasheet http://www.datasheet4u.net/
1 page Table of Contents
1 Introduction.................................................................................................................. 1
1.1 General ................................................................................................................. 1
1.2 Exhibition mode..................................................................................................... 1
1.3 Service program quick reference .......................................................................... 2
1.4 How to use the service programs.......................................................................... 4
2 Service program features ........................................................................................... 5
2.1 Sr 70 Log: Display error log .................................................................................. 5
2.2 Sr 71 PAy: Set lease period .................................................................................. 7
2.3 Sr 72 LCA: Adjust lateral TMJ image area
(film units only) ...................................................................................................... 8
2.4 Sr 74 IOC: Display CPU input/output signal check ............................................. 10
2.5 Sr 76 PUP: X-ray tube warm-up.......................................................................... 16
2.6 Sr 77 Prh: Adjust the preheat setting .................................................................. 18
2.7 Sr 78 thA: Set Dose Calibration Constant (DCC)................................................ 19
2.8 Sr 79 SUP: Display line voltage .......................................................................... 20
2.9 Sr 80 CrL: Test motor movement........................................................................ 20
2.10 Sr 81 bPL: Display biteplate properties
(Volumetric Tomography option only) ................................................................. 22
2.11 Sr 82 COL: Set/display collimator information .................................................... 23
2.12 Sr 86 Sto: Store settings ..................................................................................... 25
2.13 Sr 87 LAL: Set linear adjustment value for VT .................................................... 25
2.14 Sr 88 CAL: Disable automatic cephalostat alignment correction
(digital units only) ................................................................................................ 26
2.15 Sr 88 CAL: Set cephalostat alignment value (film units only) ............................. 27
2.16 Sr 89 COP: Set country options .......................................................................... 27
2.17 Sr 90 PIN: Panorama installation program.......................................................... 30
2.18 Sr 91 CIN: Cephalostat installation program (digital units only).......................... 31
2.19 Sr 92 CHE: Set level of self-checks .................................................................... 32
2.20 Sr 93 BAL: Adjust beam alignment board sensitivity .......................................... 33
5140241-100 rev 3
Instrumentarium Dental
i
Free Datasheet http://www.datasheet4u.net/
5 Page 2 Service program features
2 Service program features
2.1 Sr 70 Log: Display error log
Each time a failure occurs in OP200, a counter
corresponding to the failure is incremented. This program
is used to view the readings of these counters.
NOTE! Only failures that are relevant for troubleshooting
and failure diagnostics are recorded (see the table below
for details). Some failure counters have non-zero values at
the time of installation. This is normal.
5140241-100 rev 3
1. Select Sr 70 Log.
2. Press the up and down buttons to scroll the list of
counters. The control panel shows the current counter,
continually switching between its failure code and
counter value.
3. Press OK to exit the program.
FILM UNIT OP200
DIGITAL UNIT
OP200 D
kV-
display
Ch / Sy /
Er
mA-
display
error
number
Second /
dose -
display
Error name
FILM UNIT
mA-
display
error
number
Second /
dose -
display
Error name
DIGITAL
UNIT
Ch 5
*** 5
LINE VOLTAGE
***
LINE VOLTAGE
Ch 13 LbL
IMAGE LABEL
FAILURE
Ch 16 StP
16 StP
EMERGENCY
SWITCH
EMERGENCY
SWITCH
Sy 21 HHo
21 HHo
TUBEHEAD
TUBEHEAD
HOT
HOT
Instrumentarium Dental
5
Free Datasheet http://www.datasheet4u.net/
11 Page |
Páginas | Total 42 Páginas | |
PDF Descargar | [ Datasheet OC200.PDF ] |
Número de pieza | Descripción | Fabricantes |
OC200 | Orthoceph Service Program Manual | Instrumentarium |
OC200D | Orthoceph Service Program Manual | Instrumentarium |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |