|
|
PDF TG501 Data sheet ( Hoja de datos )
| Número de pieza | TG501 | |
| Descripción | Time Mark Generator Manual | |
| Fabricantes | Tektronix | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de TG501 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
Free Datasheet http://www.datasheet4u.com/
1 page  
TG 501
OPERATORS SAFETY SUMMARY
The general safety information in this part of the summary
is for both operating and servicing personnel. Specific
warnings and cautions will be found throughout the
manual where they apply, but may not appear in this
summary.
power cord into a properly wired receptacle before
connecting to the product input or output terminals. A
protective ground connection by way of the grounding
conductor in the power cord is essential for safe opera-
tion .
Terms In This Manual
CAUTION statements identify conditions or practicesthat
could result i n damage to the equipment or other property .
WARNING statements identify conditions or practices
that could result in personal injury or loss of life .
Terms As Marked on Equipment
CAUTION indicates a personal injury hazard not im-
mediately accessible as one reads the marking, or a
hazard to property including the equipment itself .
DANGER indicates a personal injury hazard immediately
accessible as one reads the marking.
Symbols As Marked on Equipment
DANGER - High voltage.
Protective ground (earth) terminal .
ATTENTION - refer to manual .
Power Source
This product is intended to operate from a power source
that will not apply more than 250 volts rms between the
supply conductors or between either supply conductor
and ground . A protective ground connection byway of the
grounding conductor in the power cord is essential for
safe operation .
Grounding the Product
This product is grounded through the grounding conduc-
tor of the power cord . To avoid electrical shock, plug the
Danger Arising From Loss of Ground
Upon loss of the protective-ground connection, all
accessible conductive parts (including knobs and con-
trols that may appear to be insulating) can render an
electric shock.
Use the Proper Power Cord
Use only the power cord and connector specified for your
product.
Use only a power cord that is in good condition.
Refer cord and connector changes to qualified service
personnel .
Use the Proper Fuse
To avoid fire hazard, use only the fuse of correct type,
voltage rating and current rating as specified in the parts
list for your product.
Refer fuse replacement to qualified service personnel .
Do Not Operate in Explosive Atmospheres
To avoid explosion, do not operate this product in an
explosive atmosphere unless it has been specifically
certified for such operation.
Do Not Operate Plug-In Unit Without Covers
To avoid personal injury, do not operate this product
without covers or panels installed. Do not apply power to
the plug-in via a plug-in extender .
@ AUG 1980
Free Datasheet http://www.datasheet4u.com/
5 Page 
Section 2-TG 501
OPERATING INSTRUCTIONS
Installation
The TG 501 is calibrated and ready for use when
received . Referring to Fig. 2-1, install the Generator and
turn on the Power Module . Check the front-panel of the
Generator to see that the knob skirt is lighted. The TG 501
is designed to operate in any compartment of a TM 500
Series Power Module . Refer to the Power Module Instruc-
tion Manual for line voltage requirements and Power
Module operation.
Refer to the Controls and Adjustments page for front-
panel controls, connectors and indicator descriptions .
Turn the Power Module off before inserting the plug-
in ; otherwise, damage may occur to the plug-in
circuitry.
CONTROLS AND CONNECTORS
MARKER Control
ORotary switch selects individual marker intervals from
5 s to 10 ns . Set to 521n position when using push buttons
for 5 ns, 2 ns and 1 ns . Readout Display is turned off in
521n position .
REV C AUG 1980
Fig. 2-1. Plug-in installation and removal.
Free Datasheet http://www.datasheet4u.com/
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet TG501.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| TG50 | (TG50 - TG55) TRANZYSTORY P-N-P |  ETC |
| TG501 | Time Mark Generator Manual | Tektronix |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |