DataSheet.es    


PDF OVC3860 Data sheet ( Hoja de datos )

Número de pieza OVC3860
Descripción AT Command Application Notes
Fabricantes OmniVision 
Logotipo OmniVision Logotipo



Hay una vista previa y un enlace de descarga de OVC3860 (archivo pdf) en la parte inferior de esta página.


Total 21 Páginas

No Preview Available ! OVC3860 Hoja de datos, Descripción, Manual

OVC3860 AT Command Application Notes
OVC3860
AT Command
Application Notes
Last Modified:2012-10-18
Document Revision:1.1
OmniVision Technologies, Inc. reserves the right to make changes without further notice to any product herein to improve
reliability, function or design. OmniVision does not assume any liability arising out of the application or use of any project,
circuit described herein; neither does it convey any license under its patent nor the right of others.
The datasheet is the official document of OmniVision. The applicaton notes are application guide lines for reference. If
there are any difference between datasheet and application notes, please follow datasheet and kindly report the
difference to OVT FAE.
This document contains information of a proprietary nature. None of this information shall be divulged to persons other
than OmniVision Technologies, Inc. employee authorized by the nature of their duties to receive such information, or
individuals or organizations authorized by OmniVision Technologies, Inc.
Company Confidential
1
Free Datasheet http://www.datasheet4u.com/

1 page




OVC3860 pdf
OVC3860 AT Command Application Notes
<CR><LF>IND<CR><LF>
<CR><LF>INDsp <CR><LF>
<CR><LF>IND ,,<CR><LF>
Among them,
— IND is basic indication
— sp is Sub-Parameter
— ,, is Sub-Parameter that may be omitted
3.3. Supported AT Commands
AT Command
CA
CB
CC
CD
CE
CF
CG
CH
CI
CJ
CM
CO
CQ*
CR*
CS*
CT*
CW<phonenum>
CX<dtmf>
CY
CZ
MA
MC
MD
ME
MF
Notion
Response Indication
Enter pairing
II
Cancel pairing
IJ2
Connect hshf
IV
Disconnect hshf
IA
Answer
IG
Reject
IF
Endcall
IF
Redial
IC
Voice call
PE/PF
Cancel voice call
OK
Toggle mic
OK
Audio transfer
MC/MD
Release held call, reject waiting call
IN
Release active call, accept other call
IT
Hold active call, accept other call
IL
Conference call
IM
Dial phone number
IC, IP<len>, IR<phonenum>
Send dtmf
OK
Query status
MG<status>
Reset
IS<ver>, MF<ab>
Play/pause
MA/MB
Stop
MA
Forward
OK
Backward
OK
Query autoconn and autoanswe
configuration
MF<ab>
Company Confidential
5
Free Datasheet http://www.datasheet4u.com/

5 Page





OVC3860 arduino
OVC3860 AT Command Application Notes
4 Command Explanations
4.1. Enter Pairing Mode #CA
Command Current Status(s) Possible Indication(s)
Indication Description
#CA Any
II
Enter Pairing Mode Indication
Description
This command puts the module in the pairing mode. The information response and causes will
indicate the command success or failure. Enter pairing mode indication or failure indication will be
sent to the host.
Note:
1.This command will cause a disconnection if module has already connected with some device.
2. Module will exit pairing mode if connection not happen in 2 minutes.
Syntax: AT#CA
4.2. Cancel Pairing Mode #CB
Command Current Status(s) Possible
Indication Description
Indication(s)
#CB Pairing
IJ2
Exit Pairing Mode Indication
Description
If the module is in pairing mode, this command causes the module to exit the pairing mode and
enter the idle mode. The information response and causes will indicate the command success or
failure.
Syntax: AT#CB
4.3. Connect HFP to Handset #CC
Command Current Status(s) Possible
Indication Description
Indication(s)
#CC
HFP Status = 1 IV
Connecting Indication
Note: You can get current HFP status by #CY.
Description
This command causes the module to connect to a paired handset. The information response and
causes will indicate the command success or failure. Connect Indication will be sent to the host
after the connection is established. Otherwise Disconnect Indication will be sent to the host.
Syntax: AT#CC
4.4. Disconnect HFP from Handset #CD
Command Current Status(s) Possible
Indication Description
Indication(s)
#CD
HFP Status ≥ 3 IA
Disconnected Indication
Description
This command causes the module to disconnect from the connected handset. The information
response and causes will indicate the command success or failure. Disconnect Indication will be
sent to the host after the connection is dropped.
Syntax: AT#CD
4.5. Answer Call #CE
Command Current Status(s) Possible
Indication(s)
Indication Description
Company Confidential
11
Free Datasheet http://www.datasheet4u.com/

11 Page







PáginasTotal 21 Páginas
PDF Descargar[ Datasheet OVC3860.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
OVC3860AT Command Application NotesOmniVision
OmniVision
OVC3860Bluetooth 2.0 + EDR Stereo Audio ProcessorOmniVision
OmniVision
OVC3860Bluetooth ModuleYIGASN
YIGASN
OVC3860Bluetooth 2.0ETC
ETC

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar