|
|
Número de pieza | VCB-3424 | |
Descripción | B/W CCD Camera Manual | |
Fabricantes | Sanyo | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de VCB-3424 (archivo pdf) en la parte inferior de esta página. Total 16 Páginas | ||
No Preview Available ! INSTRUCTION MANUAL
B/W CCD Camera
VCB-3424
About this manual
Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
1 page PARTS NAMES
1 Video output connector (VIDEO OUT: BNC type)
Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector.
3 2 Line phase adjustment volume (LINE PHASE)
1
When using two cameras or more, the image on the monitor may roll vertically when switching sources. This
rolling can be minimized by turning this volume.
2 3 Power indicator (POWER)
4 Comes on when the power to the camera is on.
4 24 V AC input terminal (24 V AC, GND)
Connect to 24 V AC UL listed class 2 power supply.
5 Camera setup section (under the cover)
These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However,
if due to installation conditions or environment the settings may need to be modified for best results (see
"SETTINGS").
5 To access the controls, loosen the cover fixing screw A, then remove the cover.
6 6 Lens iris output connector (LENS)
This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens.
A
4 English
5 Page SETTINGS
Camera setup section
a bc
BLC EI
MIR
e
VR401 L
E
V
E
L HL
DC
VIDEO
A. I.
LENS
d
Control name
a Mirror image switch (MIR)
b Backlight compensation switch (BLC)
c Electronic iris (EI)
d Auto-iris lens switch (A.I. LENS) (see page 6)
e Lens iris level volume (LEVEL)
Position
OFF
OFF
OFF
DC
about centre
Electronic iris function setting
Use a manual or fixed iris lens and set the lens
aperture to the shortest F stop. Set the EI
switch to ON position.
ON
Note:
Please refer to the specifications for dynamic
range of the electronic iris.
OFF
EI
CAUTION:
• The electronic iris is suitable for normal indoor use. When the EI
switch is set to the ON position, do not use an auto-iris lens.
• If used under fluorescent light, the image may flicker. In such a
case, change to incandescent lighting or set the EI switch to the
OFF position and use an auto-iris lens.
• When shooting bright subjects, pay attention to the light angle in
order to avoid or minimize the smear phenomenon effect.
When using an auto-iris lens (for indoor/outdoor use)
Set the EI switch to the OFF position.
CAUTION:
If conditions are outside the electronic iris operation range or more
than the maximum illumination, it will cause saturation of the CCD. In
that case, use a manual iris lens.
10 English
11 Page |
Páginas | Total 16 Páginas | |
PDF Descargar | [ Datasheet VCB-3424.PDF ] |
Número de pieza | Descripción | Fabricantes |
VCB-3424 | B/W CCD Camera Manual | Sanyo |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |