DataSheet.es    


PDF ELM407 Data sheet ( Hoja de datos )

Número de pieza ELM407
Descripción Rotary Decoder
Fabricantes ELM 
Logotipo ELM Logotipo



Hay una vista previa y un enlace de descarga de ELM407 (archivo pdf) en la parte inferior de esta página.


Total 10 Páginas

No Preview Available ! ELM407 Hoja de datos, Descripción, Manual

ELM407
Rotary Decoder - 3 wire 4x Interface
Description
The ELM407 is an 8 pin integrated circuit that is
used to convert the output from a rotary encoder into
three signals (chip select, clock and up/down) that
can be used to control various devices. The low
power CMOS technology used ensures that only a
very small current is required over the entire 2.0 to
5.5 volt operating range.
There is no need for external filtering or
debounce circuits with the ELM407, as this is all
performed within the integrated circuit. After
debouncing the encoder signals, the ELM407
determines the direction of shaft rotation, and then
generates the appropriate outputs. A write sequence
can also be generated if the Write Enable input is at
a high level when the outputs are generated.
The ELM407 provides 4x decoding of a rotary
encoder signal. If your application requires 2x
decoding, please see the ELM406 (it is identical to
the ELM407 in every respect, except that it provides
2x decoding).
Applications
• Digital audio potentiometer controls
• Variable voltage or temperature circuits
• Positioning controls
• Tuning circuits
Features
• Low power CMOS design
• Wide supply range – 2.0 to 5.5 volts
• Complete debouncing of the encoder inputs
• No external filtering needed
• 4x decoding
• Can generate a write sequence
• Startup delay timer
• High current drive outputs
Connection Diagram
PDIP and SOIC
(top view)
VDD 1
A2
B3
Write 4
Enable
8 VSS
7 CS
6 Clk
5 U/D
Block Diagram
VDD A
Debounce
2
Circuit
Direction
Output
VDD B
Decoding
Debounce
3
Circuit
Logic
Rotary
Encoder
Write 4
Enable
7 CS
6 Clk
5 U/D
ELM407DSA
Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
1 of 10
Free Datasheet http://www.datasheet4u.com/

1 page




ELM407 pdf
ELM407
Rotary Encoders
A rotary encoder (sometimes referred to as a
quadrature encoder) is a device that produces digital
(on/off) outputs in response to rotary, or circular,
motion. It is often constructed such that it looks very
much like a potentiometer, or audio volume control
(see the picture of a typical device, at the right).
As the encoder shaft is turned, internal contacts
open and close, creating two waveforms that are
ideally separated in phase by 90 degrees (ie ‘in
quadrature’). Actually, you need to provide external
‘pullup’ resistors and a power supply to create these
waveforms, as the contacts themselves can not do
this. An ideal waveform from a rotary encoder would
look like this:
A
B
Figure 1. Quadrature Waveforms
Due to the 90 degree phase difference, when one
waveform changes, the other is always stable. By
noting the direction of the change and the level of the
other input at that time, you can determine the
direction of motion of the shaft.
Rotary encoders are not ideal, however. Due to
their construction, and variations in shaft speed, the
A typical rotary encoder
waveforms are not perfectly square with the 50% duty
cycles shown. Figure 2 shows a captured trace from a
real rotary encoder that is more representative of what
you will typically find. Note that the two ‘scope
channels (1 and 2) represent the encoder outputs A
and B, respectively. The ch 1 (A) waveform leads the
ch 2 (B) waveform, which usually means that the shaft
is turning in a clockwise direction.
The first rising edge of the channel 2 waveform
shows another problem that occurs with moving
mechanical contacts - multiple pulses due to bounce.
When two contacts meet, the moving one will tend to
bounce, like a ball does when it is dropped on the
floor. Each bounce results in an electrical connection
being made, then broken, which will look like multiple
inputs to a fast electronic circuit. Various mechanical
means are used to reduce the amount of bounce, but it
can never really be eliminated. The following section
discusses how the ELM407 uses electronic means to
remove the bounce.
ELM407DSA
Figure 2. Actual Rotary Encoder waveform
Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
5 of 10
Free Datasheet http://www.datasheet4u.com/

5 Page










PáginasTotal 10 Páginas
PDF Descargar[ Datasheet ELM407.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
ELM401Rotary Encoder Debounce CircuitELM
ELM
ELM402Rotary DecoderELM
ELM
ELM403Rotary DecoderELM
ELM
ELM404Rotary DecoderELM
ELM

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar