|
|
Número de pieza | CAT6202 | |
Descripción | CMOS LDO Regulator | |
Fabricantes | ON Semiconductor | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de CAT6202 (archivo pdf) en la parte inferior de esta página. Total 10 Páginas | ||
No Preview Available ! CAT6202
500 mA / 13 V Adjustable
CMOS LDO Regulator
Description
The CAT6202 is a 13 V rated 500 mA CMOS low dropout regulator
that provides fast response time to load current and line voltage
changes in an automotive environment.
CAT6202 features a low RON P−channel pass element with internal
control circuitry which prevents reverse current flow should the
voltage at VOUT exceed VIN as in the case of the car’s battery voltage
accidentally being applied to VOUT.
Thermal protection and current limiting circuitry combine to protect
the pass device against faults and abuse. Current limiting is user
controlled through a single resistor to ground. A fault output (FLT)
provides an alert should an over−current event or thermal shutdown
occur.
CAT6202 comes on−line gracefully even though it may be driving
heavy capacitive loads thanks to built−in soft−start circuitry. Its output
is protected against accidental connection to voltages greater than VIN
and will not conduct current backwards into its supply.
CAT6202 is available in 8−pad 2 mm x 3 mm TDFN package.
Features
• Guaranteed 500 mA Continuous Output Current
• Low Dropout Voltage of 250 mV Typical at 500 mA
• Input Voltage Range: 3.3 V to 13.5 V
• User Adjustable Output Voltage
• User Programmable Current Limit
• Fault Output to Indicate Under−voltage, Current Limiting or Thermal
Shutdown has Occurred
• Fault Blanking: 3 ms
• VOUT Withstands Battery Fault Voltages of up to 14 V
• Soft−Start Prevents Current Surges
• Stable with Ceramic Output Capacitor
• ±1.0% Output Voltage Initial Accuracy
• ±2.0% Accuracy Over Temperature
• Thermal Protection
• 8 Pad TDFN Package
• These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
http://onsemi.com
TDFN−8
VP2 SUFFIX
CASE 511AK
PIN CONNECTIONS
VIN
FLT
EN
BYP
1
VOUT
VADJ
ILIM
GND
TDFN−8
(Top View)
MARKING DIAGRAMS
HKC
LAA
YM
G
HKC
L
AA
Y
M
G
= CAT6202VP2−GT3
= Assembly Location
= Last Two Digits of
= Assembly Lot Number
= Production Year (Last Digit)
= Production Month (1−9, O, N, D)
= Pb−Free Microdot
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 10 of this data sheet.
© Semiconductor Components Industries, LLC, 2012
October, 2012 − Rev. 0
1
Publication Order Number:
CAT6202/D
Free Datasheet http://www.datasheet4u.com/
1 page CAT6202
Table 4. ELECTRICAL CHARACTERISTICS
(VIN = VOUT + 1 V, VEN = High, IOUT = 1 mA, CIN = 1 mF, COUT = 2.2 mF, REXT = 47 kW, ambient temperature of 25°C (over recommended
operating conditions unless specified otherwise). Bold numbers apply for the entire junction temperature range.)
Symbol
Parameter
Conditions
Min
Typ Max
Unit
VIN
VOUT
VADJ
IADJ
TCOUT
VR−LINE
Input Voltage
Output Voltage
ADJ Voltage
ADJ Input Current
Output Voltage Temp. Coefficient
Line Regulation
VOUT + 1.0 < VIN < 13 V
3.3
VADJ
1.238
0.5
−0.2
−0.4
1.250
40
±0.1
13.5
12.5
1.262
2.0
+0.2
+0.4
V
V
mA
ppm/°C
%/V
VR−LOAD
VDROP
IGND
Load Regulation
Dropout Voltage (Note 3)
Ground Current
IGND−SD
PSRR
Shutdown Ground Current
Power Supply Rejection Ratio
TON Turn−On Time
ISC Output short circuit current
ILIM Output current limit
CLF Current Limit Factor
tFD Fault Delay
VIN−UVLO Under voltage lockout threshold
ESR
ROUT equivalent series resistance
ENABLE INPUT
IOUT = 1 mA to 500 mA
IOUT = 500 mA
IOUT = 0 mA
IOUT = 500 mA
VEN < 0.4 V
f = 1 kHz, CBYP = 10 nF
f = 20 kHz, CBYP = 10 nF
CBYP = 10 nF
VOUT < 0.8 V
VOUT = 0.8 VOUT (1 mA)
VOUT < 0.8 V
1 2.5
%
250 350
mV
100 150
mA
160 300
2 mA
62 dB
52
700 ms
700
800 1000
mA
600 650 800 mA
24 30 36 KV
1.5 3 6 ms
3.1 V
5 500 mW
VHI Logic High Level
VLO Logic Low Level
IEN Enable Input Current
THERMAL PROTECTION
VIN = 3.3 to 13 V
VIN = 3.3 to 13 V
VEN = 0.4 V
VEN = VIN
2V
0.4 V
0.15 1
mA
35
TSD Thermal Shutdown
140 °C
THYS
Thermal Hysteresis
10 °C
3. Dropout voltage is defined as the input−to−output differential at which the output voltage drops 2% below its nominal value. During test, the
input voltage stays always above the minimum 3.3 V. The given values are for VOUT = 7.5 V.
http://onsemi.com
5
Free Datasheet http://www.datasheet4u.com/
5 Page |
Páginas | Total 10 Páginas | |
PDF Descargar | [ Datasheet CAT6202.PDF ] |
Número de pieza | Descripción | Fabricantes |
CAT6201 | 300 mA / 13 V Adjustable CMOS LDO Regulator | ON Semiconductor |
CAT6202 | CMOS LDO Regulator | ON Semiconductor |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |