DataSheet.es    


PDF F930J226MBA Data sheet ( Hoja de datos )

Número de pieza F930J226MBA
Descripción (F93 Series) Solid Tantalum Electrolytic Capacitors
Fabricantes Nichicon 
Logotipo Nichicon Logotipo



Hay una vista previa y un enlace de descarga de F930J226MBA (archivo pdf) en la parte inferior de esta página.


Total 2 Páginas

No Preview Available ! F930J226MBA Hoja de datos, Descripción, Manual

www.DataSheet4U.com
SOLID TANTALUM ELECTROLYTIC CAPACITORS
F93 Resin-molded Chip,
Standard Series
Specifications
Item
Performance Characteristics
Category
Temperature Range
--55 ~ +125˚C (Rated temperature : 85˚C)
Capacitance Tolerance ± 20%, ± 10% (at 120Hz)
Dissipation Factor
Refer to P.217
E.S.R.
Leakage Current
Capacitance Change
by Temperature
Refer to P.217
After 1 minute's application of rated voltage, leakage current
at 20˚C is not more than 0.01CV or 0.5µA, whichever is greater.
After 1 minute's application of rated voltage, leakage current
at 85˚C is not more than 0.1CV or 5µA, whichever is greater.
After 1 minute's application of derated voltage, leakage current
at 125˚C is not more than 0.125CV or 6.3µA, whichever is greater.
+15% Max. (at +125˚C)
+10% Max. (at +85˚C)
--10% Max. (at --55˚C)
Type numbering system (Example: 10V 10µF)
Damp Heat
(No voltage applied)
At 40˚C 90 ~ 95% R.H. 500 hours
Capacitance Change Within ±10% of initial value
Dissipation Factor......Initial specified value or less
Leakage Current........Initial specified value or less
--55˚C / +125˚C 30 minutes each 5 cycles
123
F93
45
1A
678
106
9 10 11
MA
Taping code
(Refer to page 211 for details)
Case code
Capacitance tolerance
Rated Capacitance Rated voltage
Series
Temperature Cycles
Resistance
to Soldering Heat
Capacitance Change Within ±5% of initial value
Dissipation Factor......Initial specified value or less
Leakage Current........Initial specified value or less
Test condition:
5 seconds immersion at 260˚C,10 seconds reflow at 260˚C
Capacitance Change Within ±5% of initial value
Dissipation Factor......Initial specified value or less
Leakage Current........Initial specified value or less
Drawing
After application of surge voltage in series with a 33resistor at the rate of
30 seconds ON, seconds OFF, for 1000 sucessive test cycles at 85˚C,
A B Case
L
W1
C N Case
L W1
Surge
capacitors meet the characteristics requirements listed below.
Capacitance Change....Within ±5% of initial value
Dissipation Factor........Initial specified value or less
Leakage Current..........Initial specified value or less
After 2000 hours' application of rated voltage in series with a 3resistor
H
W2
SS
H
W2
SS
Endurance
at 85˚C, or derated voltage in series with a 3resistor at 125˚C,
capacitors meet the characteristic requirements listed below.
Capacitance Change......Within ±10% of initial value
Dissipation Factor..........Initial specified value or less
Leakage Current............Initial specified value or less
DataSheeAfter applying the pressure load of 5N for 10±1 seconds
horizontally to the center of capacitor side body which has no
Dimensions
Case code
A
B
C
N
L
3.2 ± 0.2
3.5 ± 0.2
6.0 ± 0.2
7.3 ± 0.2
Marking
A Case
C685
W1
1.6 ± 0.2
2.8 ± 0.2
3.2 ± 0.2
4.3 ± 0.2
W2
1.2 ± 0.1
2.2 ± 0.1
2.2 ± 0.1
2.4 ± 0.1
H
1.6 ± 0.2
1.9 ± 0.2
2.5 ± 0.2
2.8 ± 0.2
B Case
22
16V
C Case
(mm)DataSheet4US.hceaor mTest
S
0.8 ± 0.2
0.8 ± 0.2
1.3 ± 0.2
1.3 ± 0.2
Terminal Strength
N Case
electrode and has been soldered
beforehand on an aluminum substrate,
neigher exfoliation not its sign shall be
found at the terminal electrode.
5N (0.51kg f)
For 10±1seconds
Keeping a capacitor surface-mounted on a substrate upside down
and supporting the substrate at both of the opposite bottom points
45mm apart from the center of the capacitor, the
pressure load is applied with a
specified jig at the center of the
R230
20
substrate so that the substrate may
bend by 1mm as illustrated.
Then, there shall be found no
remarkable abnormality on the
capacitor terminals.
45 45
As for the surge and derated voltage at 125˚C, refer to page 210 for details.
(Rated voltage code)
2.5V
4V
6.3V
10V
16V
e
G
J
A
C
20V
25V
35V
(Capacitance code)
D
E
V
Rated voltage (V)
Capacitance (µF)
Rated voltage (V)
Standard ratings
Cap. (µF)
0.47
0.68
1
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
150
220
DataSheet4U3.3c0om
470
680
1000
V
Code
474
684
105
155
225
335
475
685
106
156
226
336
476
686
107
157
227
337
477
687
108
2.5
0E
A
A
A
AB
AB
BC
BC
BC
CN
CN
4 6.3 10
0G 0J 1A
A
A
A
A
AB
AB
AB
ABC
A B C
BC
(B) C N
CN
N
N
(N)
A
A
A
A
A
A B
AB
A B
AB
BC
BC
(B) C N
CN
N
N
(N)
A
A
A
A
AB
A B
A B
(A) B C
BC
(B) C N
CN
(C) N
N
N
(N)
DataSheet4 U .com
16
1C
A
A
A
A
A
A B
A B
A B
BC
C
CN
N
N
20
1D
A
A
A
A
A B
A B
B
C
C
N
N
25
1E
A
A
A
A
A B
B
C
C
N
N
35
1V
A
A
A
A
B
B
C
C
N
N
( ) The series in parentheses are being developed.
Please contact to your local Nichicon sales office when these
series are being designed in your application.
CAT.8100R

1 page





PáginasTotal 2 Páginas
PDF Descargar[ Datasheet F930J226MBA.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
F930J226MBA(F93 Series) Solid Tantalum Electrolytic CapacitorsNichicon
Nichicon

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar