DataSheet.es    


PDF MT1102 Data sheet ( Hoja de datos )

Número de pieza MT1102
Descripción Hall-Effect Magnetic Position Sensors
Fabricantes MagnTek 
Logotipo MagnTek Logotipo



Hay una vista previa y un enlace de descarga de MT1102 (archivo pdf) en la parte inferior de esta página.


Total 5 Páginas

No Preview Available ! MT1102 Hoja de datos, Descripción, Manual

MT1102
CMOS Unipolar, Hall-Effect Magnetic Position Sensors
FEATURES
s Resistant to Physical Stress
s Superior Temperature Stability
s Chopper stablized amplifier
s Operation From Unregulated Supply
s High sensitivity
s Solid-State Reliability
s Open Drain output
s Small Size
These Hall-effect sensors are monolithic integrated circuits with
tighter magnetic specifications, designed to operate continuously over
extended temperatures to +125°C, and are more stable with both
temperature and supply voltage changes.
Each device includes a voltage regulator for operation with supply
voltages of 3.5 to 24 volts, hall plate with dynamic cancellation
system, temperature compensation circuitry, chopper stablized small-
signal amplifier, Schmitt trigger, and an open drain output to sink
up to 50 mA. With suitable output pull up, they can be used with
bipolar or CMOS logic circuits.
This sensor family includes most widely used industry package
type with same die inside:
MT1102A --- TO-92S
MT1102AT --- SOT-23
MT1102BT --- SOT-89B
ABSOLUTE MAXIMUM RATINGS
at TA = +25°C
Supply Voltage, VCC ........................ 28 V
Magnetic Flux Density, B ........... Unlimited
Output Off Voltage, VOUT ...................28 V
Continuous Output Current,
IOUT .......................................... 50 mA*
Reverse Output Current, IOUT ........ -50 mA
Junction Temperature, TJ .............. +150°C
Operating Temperature Range, T
A
-50°C to +125°C
Storage Temperature Range,
TS .............................. -50°C to +150°C
* Only when the Vcc=4.5V
Block Diagram
1 MagnTek Sensing technology
Free Datasheet http://www.datasheet4u.com/

1 page




MT1102 pdf
MT1102
CMOS Unipolar, Hall-Effect Magnetic Position Sensors
PACKAGE DESIGNATOR
(MT1102A)
4.10
4.01
1.57
45° 1.47
Radial Lead Form (order MT1101A-T)
3.10
2.97
2.16 1 2 3 0.79
MAX
16.26
15.24
SEE NOTE
0.48
0.36
1.27
BSC
0.44
0.35
0.620"
0.500"
(15.7 mm
12.7 mm)
123
0.108"
(2.74 mm)
0.100"
(2.5 mm)
NOTES: 1.
2.
3.
4.
5.
6.
Tolerances on package height and width represent
allowable mold offsets. Dimensions given are
measured at the widest point (parting line).
Exact body and lead configuration at vendor’s option
within limits shown.
Height does not include mold gate flash.
Recommended minimum PWB hole diameter to clear
transition area is 0.035" (0.89 mm).
Where no tolerance is specified, dimension is nominal.
Supplied in bulk pack (500 pieces per bag).
NOTE: Lead-form dimensions are the nominals produced on the
forming equipment. No dimensional tolerance is implied or
guaranteed for bulk packaging (1000 pieces per bag).
2
5 MagnTek Sensing technology
Free Datasheet http://www.datasheet4u.com/

5 Page










PáginasTotal 5 Páginas
PDF Descargar[ Datasheet MT1102.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
MT110Thyristor ModulesTECHSEM
TECHSEM
MT1102Hall-Effect Magnetic Position SensorsMagnTek
MagnTek
MT1102AHall-Effect Magnetic Position SensorsMagnTek
MagnTek
MT1102A-THall-Effect Magnetic Position SensorsMagnTek
MagnTek

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar